![background image](http://html1.mh-extra.com/html/danfoss/vlt-brook-crompton-motor-fcm-300/vlt-brook-crompton-motor-fcm-300_design-manual_3509314024.webp)
Fitting pinions, pulleys and couplings.
These should be bored to our standard limits and fitted on
the shaft with a screwing motion. Attention must be paid
to correct guarding of all moving parts.
NOTICE
Tapping of fittings onto the FC motor shaft, with a
hammer or mallet, causes bearing damage. This results
in an increase in bearing noise and a significant
reduction in bearing life.
NOTICE
Max. the B14 flange, see
.
2.2.6 Alignment
When the application calls for direct coupling, the shafts
must be correctly aligned in all three planes. Bad
alignment can be a major source of noise and vibration.
Allowance must be made for shaft endfloat and thermal
expansion in both axial and vertical planes. It is preferable
to use flexible drive couplings.
Horizontal shaft
Vertical shaft
Shaft up
Shaft down
Type
Poles
Load towards
motor
Load away
from motor
Load towards
motor
Load away
from motor
Load up
Load
down
Maximum
permissible radial
load at the end of
shaft (horizontal
mounting)
W-DA80
2
339
539
321
565
362
521
774
4
303
503
283
530
330
583
729
W-DA90
2
444
684
421
716
476
661
915
4
398
638
366
682
442
606
854
W-DA100
2
781
1101
743
1159
839
1063
1295
4
710
1030
655
1107
787
975
1215
W-DA112
2
768
1088
715
1170
850
1035
1295
4
690
1010
612
1131
811
932
1202
W-DA132
2
1355
1707
1266
1838
1486
1618
2114
4
1253
1605
1130
1779
1427
1482
2068
Table 2.19 Maximum Permissible External Axial and Radial Loads in Newtons
2.2.7 Bolt Torques
Endshields and lid should be secured with the bolt sizes
and torques detailed in
FCM Type
Frame size
Bolt diameter Nm.
Torque
305-307
80
M5
5
311-315
90
M5
5
322-330
100
M6 (taptite)
8-10
340
112
M6 (taptite)
8-10
355-375
132
M8 (taptite)
29
LID screws torque: 2.2-2.4 Nm
Table 2.20 Endshield Fixing Bolt Torques
2.2.8 Maintenance
Routine cleaning of the FC motor
Remove the fan cover and ensure that all air inlet holes
are completely free. Clean any dirt and obstructions from
behind the fan and along the ribs of the frame, and
between the motor and inverter part.
Periodic maintenance of motor part
1.
Remove the inverter part, the fan cover and the
fan which is keyed to the shaft extension. Loosen
and remove bearing cover screws and endshield
bolts/studs. The endshields should then be eased
off their spigots.
2.
The rotor can now be carefully withdrawn from
the stator, taking care not to damage the stator
bore and both stator and rotor windings.
3.
Having dismantled the motor, maintenance can
be carried out to remove all dirt. For this
purpose, the use of an air line supplying dry
compressed air under comparatively low pressure
is best, as a high velocity air-stream can force dirt
Installation
VLT
®
DriveMotor FCM Series
22
MG03BA02 - VLT
®
is a registered Danfoss trademark
2
2
Содержание VLT Brook Crompton Motor FCM 300
