Danfoss VLT Brook Crompton Motor FCM 300 Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 102

background image

1 Introduction

1.1 Safety

1.1.1 Software Version

FCM 300 Series

Design Guide

Software version: 3.1x

This Design Guide can be used for all FCM 300 Series frequency
converters with software version 3.1x.
The software version number can be seen from parameter 624
Software version no.

Table 1.1

1.1.2 Disposal Instruction

Equipment containing electrical
components may not be disposed of
together with domestic waste.
It must be separately collected with
electrical and electronic waste according
to local and currently valid legislation.

Table 1.2

1.1.3 Symbols

The following symbols are used in this Design Guide and
require special attention.

WARNING

Indicates a potentially hazardous situation which, if not
avoided, could result in death or serious injury.

NOTICE

Indicates highlighted information that should be
regarded with attention to avoid mistakes or operate
equipment at less than optimal performance.

CAUTION

Indicates a potentially hazardous situation which, if not
avoided, may result in minor or moderate injury. It may
also be used to alert against unsafe practices.

1.1.4 General warnings

NOTICE

All operations must be carried out by appropriately
trained personnel.
Use all lifting facilities provided e.g. both lifting points if
fitted or single lifting point if fitted*.
Vertical lifting - Prevent uncontrolled rotation.
Lift machine - Do not lift other equipment with motor
lifting points only.
Before installation check for fan cover damage, shaft
damage, foot/mounting damage, and loose fasteners.
Check nameplate details.
Ensure level mounting surface, balanced mounting, not
misaligned.
Gaskets, and/or sealants, and guards must be correctly
fitted.
Correct belt tension.

Please observe derating rules, see

4.1 Special Conditions

*Note: maximum hand lift is 20 kg below shoulder, but
above ground level. Max. gross weights:

-

Frame size 80: 15 kg

-

Frame size 90 & 100: 30 kg

-

Frame size 112: 45 kg

-

Frame size 132: 80 kg

WARNING

The voltage on the FC motor is dangerous when the
motor is connected to mains. Incorrect installation of the
FC motor may lead to material damage or serious injury,
or it may be fatal.
Consequently, the instructions in this manual as well as
national and local rules and safety regulations must be
complied with.
Touching the electrical parts may be fatal, even after the
mains supply has been disconnected. Wait at least 4
minutes.
- Installation must be fused and isolated correctly.
- Covers and cable entries must be fitted.

WARNING

By altitudes above 2 km, please contact
Danfoss Drives regarding PELV.

Introduction

VLT

®

DriveMotor FCM Series

4

MG03BA02 - VLT

®

is a registered Danfoss trademark

1

1

«
...
4
5
6
7
8
...
»

Содержание VLT Brook Crompton Motor FCM 300







































































































Отзывы:

Нет отзывов

Похожие инструкции для VLT Brook Crompton Motor FCM 300

Бренд: DAF Страницы: 87

Бренд: GAPOSA Страницы: 20

Бренд: Polini Страницы: 32

Бренд: Vanguard Страницы: 120

Бренд: Jiecang Страницы: 2

Бренд: DLE Страницы: 4

Бренд: O.S. engine Страницы: 15

Бренд: Wilesco Страницы: 4

Бренд: YS Страницы: 2

Бренд: Honda Страницы: 46

Бренд: O.S. engine Страницы: 21

Бренд: Krick Страницы: 12

Бренд: Briggs & Stratton Страницы: 12

Бренд: HPI Racing Страницы: 16

Бренд: Briggs & Stratton Страницы: 10

Бренд: Cub Cadet Страницы: 40

Бренд: KTM Страницы: 11

Бренд: SKY Engines Страницы: 49

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды