Danfoss VLT Brook Crompton Motor FCM 300 Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 102

background image

B14 FCM

305/307

311/315

322/330

340

355/375

Frame size

56

63

71

80

90

100

112

132

IEC Ref.

FT65

FT75

FT85

FT100

FT115

FT130

FT130

FT165

DIN Ref.

C80

C90

C105

C120

C140

C160

C160

C2OO

C [mm]

50

56

63

70

89

M [mm]

65

75

85

100

115

130

130

165

N [mm]

50

60

70

80

95

110

110

130

P [mm]

80

90

105

120

140

160

164

200

S [mm]

M5

M6

M6

M8

M8

M8

M10

T [mm]

2.5

2.5

3

3

3.5

3.5

3.5

LA [MM]

9

9

9

9

8.5

13

13

Max. the B14
flange

8.5

11

11

11.5

15

15.5

17

Table 2.18 Face Mounting - B14, B34 (B3+B14)

2.2.5 Installation of the FC Motor

Illustration 2.4

FC motors must be installed with adequate access for
routine maintenance. A minimum of 0.75 m of working
space around the motor is recommended. Adequate space
around the motor, particularly at the fan inlet (50 mm), is
also necessary to facilitate airflow.
Where several FC motors are installed in close proximity,
care must be taken to ensure that there is no recirculation
of exhausted warm air. Foundations must be solid, rigid
and level.

NOTICE

Electrical installation
Do not remove the top foil inside the inverter part, as
this is a part of the protective arrangements.

Installation

VLT

®

DriveMotor FCM Series

MG03BA02 - VLT

®

is a registered Danfoss trademark

21

2

2

«
...
21
22
23
24
25
...
»

Содержание VLT Brook Crompton Motor FCM 300







































































































Отзывы:

Нет отзывов

Похожие инструкции для VLT Brook Crompton Motor FCM 300

Бренд: Perkins Страницы: 92

Бренд: Nissei Страницы: 16

Бренд: Man Страницы: 92

Бренд: AUSTAR Страницы: 11

Бренд: JVL Страницы: 306

Бренд: JVL Страницы: 347

Бренд: Habasit Страницы: 54

Бренд: Valach Страницы: 24

Grove - Servo Max

Бренд: Seeed Страницы: 9

Бренд: Alutech Страницы: 32

Бренд: Honda Страницы: 42

Бренд: LONCIN Страницы: 26

Бренд: Toyota Страницы: 78

Бренд: KTM Страницы: 28

Бренд: Seidel Страницы: 17

Бренд: E-FLITE Страницы: 3

Power 25 Brushless Outrunner

Бренд: E-FLITE Страницы: 4

Parilla MINI SWIFT

Бренд: IAME Страницы: 31

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды