Danfoss FC322 Series, Инструкция по эксплуатации

Страница: 174 / 186

Protection and Features:
• Electronic thermal motor protection against overload.
• Temperature monitoring of the heatsink ensures that the frequency converter trips if the temperature reaches 95 °C ± 5°C. An overload tem-
perature cannot be reset until the temperature of the heatsink is below 70 °C ± 5°C (Guideline - these temperatures may vary for different
power sizes, enclosures etc.). Automation VT Drive has an auto derating function to avoid it's heatsink reaching 95 °C.
• The frequency converter is protected against short-circuits on motor terminals U, V, W.
• If a mains phase is missing, the frequency converter trips or issues a warning (depending on the load).
• Monitoring of the intermediate circuit voltage ensures that the frequency converter trips if the intermediate circuit voltage is too low or too high.
• The frequency converter is protected against earth faults on motor terminals U, V, W.
Mains supply (L1, L2, L3):
Supply voltage
200-240 V ±10%
Supply voltage 380-480 V ±10%
Supply voltage 525-600 V ±10%
Supply voltage 525-690 V ±10%
Mains voltage low / mains drop-out:
During low mains voltage or a mains drop-out, the FC continues until the intermediate circuit voltage drops below the minimum stop level, which
corresponds typically to 15% below the FC's lowest rated supply voltage. Power-up and full torque cannot be expected at mains voltage lower than
10% below the FC's lowest rated supply voltage.
Supply frequency 50/60 Hz +4/-6%
The frequency converter power supply is tested in accordance with IEC61000-4-28, 50 Hz +4/-6%.
Max. imbalance temporary between mains phases 3.0 % of rated supply voltage
True Power Factor ( λ ) ≥ 0.9 nominal at rated load
Displacement Power Factor (cos φ ) near unity (> 0.98)
Switching on input supply L1, L2, L3 (power-ups)
≤
enclosure type A maximum 2 times/min.
Switching on input supply L1, L2, L3 (power-ups)
≥
enclosure type B, C maximum 1 time/min.
Switching on input supply L1, L2, L3 (power-ups)
≥
enclosure type D, E, F maximum 1 time/2 min.
Environment according to EN60664-1 overvoltage category III/pollution degree 2
The unit is suitable for use on a circuit capable of delivering not more than 100.000 RMS symmetrical Amperes, 240/480 V maximum.
Motor output (U, V, W):
Output voltage
0 - 100% of supply voltage
Output frequency 0 - 1000 Hz *
Switching on output Unlimited
Ramp times 1 - 3600 sec.
* Dependent on power size.
Torque characteristics:
Starting torque (Constant torque) maximum 110% for 1 min. *
Starting torque maximum 135% up to 0.5 sec. *
Overload torque (Constant torque) maximum 110% for 1 min. *
*Percentage relates to Automation VT Drive nominal torque.
Cable lengths and cross sections:
Max. motor cable length, screened/armoured
Automation VT Drive: 150 m
Max. motor cable length, unscreened/unarmoured Automation VT Drive: 300 m
Max. cross section to motor, mains, load sharing and brake *
Maximum cross section to control terminals, rigid wire
1.5 mm
2
/16 AWG (2 x 0.75 mm
2
)
Maximum cross section to control terminals, flexible cable 1 mm 2 /18 AWG
Maximum cross section to control terminals, cable with enclosed core 0.5 mm 2 /20 AWG
Minimum cross section to control terminals 0.25 mm 2
* See Mains Supply tables for more information!
10 Specifications
Automation VT Drive FC322
Instruction Manual
174
MG.20.U1.22
10