Danfoss AK2-SC 255 Скачать руководство пользователя страница 74 | Manualshive

Страница: 74 / 206

Danfoss AK2-SC 255 Скачать руководство пользователя страница 74

RS.8D.M1.22

AK2-SC 255 Reference Manual

73

RTU dehumidification
configuration

Begin by selecting Dehumidify from the Configure RTU menu.

Dehumidification type

(List box: None, Cooling, Dessicant Whl) The type of
dehumidification used.

Rclm heat during dehumid (List box: Yes, No) Whether or not heat reclaim is

allowed during dehumidification.

Aux heat during dehumid

(List box: Yes, No) Whether or not auxiliary heat is

allowed during dehumidification.

Control dehumid. on

(List box:)
Humidity: Dehumidification will be controlled based

on a specified humidity target. A humidity sensor is
required.

Calc InDew: Dehumidification will be controlled

based on a specified dewpoint target, which will be
compared with a dewpoint calculated from inside zone
temperatuare and humidity. Both zone temperature
and humidity sensors must be installed.

Inside Dew: Dehumidification will be controlled

based on a specified inside dewpoint target. An inside
dewpoint sensor is required.

Calc OutDew: Dehumidification will be controlled

based on a specified dewpoint target, which will be
compared with a dewpoint calculated from outside
temperatuare and humidity. Outside temperature and
humidity sensors must be installed.

Outside Dew: Dehumidification will be controlled

based on a specified outside dewpoint target. An
outside dewpoint sensor is required.

Control sensor

(List box, if controlled by dewpoint or humidity only,

and if there are multiple sensors:)

Min Humidity or Min dewpoint : Control will be

based on the lowest-reading of a group of sensors.

«
...
72
73
74
75
76
...
»

Содержание AK2-SC 255















































































































































































































Отзывы:

Нет отзывов