Danfoss AK2-SC 255 Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 206

Danfoss AK2-SC 255 Скачать руководство пользователя страница 17

16

AK2-SC 255 Reference Manual

RS.8D.M1.22

digital input from a phase loss monitor.

Generate input for each

[appears only after a Yes answer to the preceding
question] (List box) Whether there is a phase loss
input for each rack or each suction group.

Shutdown phase loss

[appears only after a Yes answer to the Monitor phase
loss question] (List box: Yes, No)

When all of the items on the Rack Info screen have been configured, press MENU to
return to the Main Menu.

Adding a Rack

There is only one way to add a rack. From the Main Menu select Configuration,
then Refrigeration, and the Rack Configuration screen appears. At the bottom left of
the screen are the words >> Add Rack<<. Move the cursor there and press
ENTER. A new Rack Info screen will appear.

Notice that the Rack Label field contains the letter B by default, since the previously
configured rack was rack A. You can change the default label if you want.

Configuring
Suction Info

To configure a suction group, press MENU to return to the Main Menu, then select
Configuration, then Refrigeration. The Rack Configuration screen appears as at
left above. Select the rack and a Configure Rack menu appears (as at left below) .

«
...
15
16
17
18
19
...
»

Содержание AK2-SC 255















































































































































































































Отзывы:

Нет отзывов