Danfoss AK2-SC 255 Скачать руководство пользователя страница 194 | Manualshive

Страница: 194 / 206

Danfoss AK2-SC 255 Скачать руководство пользователя страница 194

RS.8D.M1.22

AK2-SC 255 Reference Manual

193

2.7 Using the Alarms Screens

The Alarms Menu

From the main menu, select Alarms and the Alarm Menu appears:

The menu items are as follows:

Active Alarms An active alarm is any alarm whose condition is still out of

bounds, whether or not the alarm has been acknowledged.
Any active alarms among the most recent 100 alarms will be
displayed in the Active Alarms screen.

Cleared Alarms

A cleared alarm is any alarm which has occurred but
whose condition is no longer out of bounds, whether or not
the alarm has been acknowledged. Any cleared alarms
among the most recent 100 alarms will be displayed in the
Cleared Alarms screen.

Alarm Status

Alarm status lists every configured alarm, and its current
state, for this SC 255.

Network Alarms

Network alarms lists every alarm in the system (the entire
network of SC 255’s) which is active or cleared. Up to 100
alarms will be listed in chronological order with the most
recent alarm first. Alarms which reoccur can appear more
than once.

Configuration Configuration takes you to the Alarm Configuration Menu.

Alarm configuration is covered in Part One of this manual.

«
...
192
193
194
195
196
...
»

Содержание AK2-SC 255















































































































































































































Отзывы:

Нет отзывов