Danfoss AK2-SC 255 Скачать руководство пользователя страница 176

Страница: 176 / 206

RS.8D.M1.22

AK2-SC 255 Reference Manual

175

Defrost:

The circuit is undergoing a scheduled defrost.

Manual:

The circuit has been set manually on or manually off

by means of the service screen.

Shutdown:

The circuit is in a scheduled shutdown.

The remaining fields are self-explanatory.

Evaporator Settings
Screen

The settings screen, reached by selecting the settings icon at the bottom of the screen,
shows and allows changes to settings for refrigeration and defrost:

Evaporator Schedules
Screen

The evaporator schedules screen shows defrost schedule information and allows
changes to number of defrosts, duration, and start times.

Evaporator Alarms
Screen

The evaporator alarms screen lists all active alarms for the circuit.

Evaporator Service
Screen

The evaporator service screen is covered in

Содержание AK2-SC 255















































































































































































































Результаты поиска

Содержание AK2-SC 255

Отзывы:

Danfoss AK2-SC 255, Справочное руководство, Страница: 176 / 206

Результаты поиска

Содержание AK2-SC 255

Отзывы: