Danfoss AK2-SC 255 Скачать руководство пользователя страница 66 | Manualshive

Страница: 66 / 206

Danfoss AK2-SC 255 Скачать руководство пользователя страница 66

RS.8D.M1.22

AK2-SC 255 Reference Manual

65

Fan type

(List box:)
1-Speed: The unit has a single-speed fan.
2-Speed: The unit has a two-speed fan.

Fan control OPEN hours

(List box:)
Continuous: The fan will run continuously during
open hours. Store open hours are defined in the Store
Info screens.
On demand: The fan will run on demand during open
hours. “On demand” means that the fan will run
whenever conditions calling for heating, heat reclaim,
cooling, dehumidification, or venting are met.

Fan control CLOSED hours(List box:)

Continuous: The fan will run continuously during

closed hours. Store closed hours are defined in the
Store Info screens.

On demand: The fan will run on demand during
closed hours. “On demand” means that the fan will run
whenever conditions calling for heating, heat reclaim,
cooling, dehumidification, or venting are met.

Post delay

(0 to 60) The number of minutes that the fan will run
after the last stage of heating, cooling, etc. is turned
off.

RTU Fan
configuration , page 2

Monitor phase loss

(List box: Yes, No) Whether or not a phase loss
monitor will be monitored.

Shutdown on phase loss

(List box: Yes, No) Whether or not the unit is to be
shut down when its phase loss detector input is on.

Which phase loss

(List box: ) All available phase loss monitors are
shown.

Shutdown on smoke detect (List box: Yes, No) Whether or not the unit is to be

shut down when its smoke detector is on.

Shutdown on fire alarm

(List box: Yes, No) Whether or not the unit is to be
shut down when a monitored fire alarm is detected.

«
...
64
65
66
67
68
...
»

Содержание AK2-SC 255















































































































































































































Отзывы:

Нет отзывов