Danfoss AK2-SC 255 Скачать руководство пользователя страница 48

Страница: 48 / 206

RS.8D.M1.22

AK2-SC 255 Reference Manual

earlier section on evaporator (defrost) configuration. The screen is not shown here.

Receiver
configuration

To configure the receiver, return to the Configure Rack menu, put the cursor on
Receiver, and press ENTER. The screen is as shown below.

Surge control

(List box: Yes, No) Whether or not surge control will

be implemented.

Cutin

(0.0 to 100.0) The temperature at which the surge
valve opens.

Cutout

(0.00 to 100.0) The temperature at which the surge
valve closes.

Liquid level sensor type

(List box:)
Sensor input: An analog sensor is used for liquid
level.
On/Off input: A digital sensor is used for liquid level.
None: There is no liquid level sensor monitored.

Heat reclaim
configuration

To configure heat reclaim, return to the Configure Rack menu, put the cursor on Heat
Reclaim, and press ENTER. The screen is as shown below.

Содержание AK2-SC 255















































































































































































































Результаты поиска

Содержание AK2-SC 255

Отзывы:

Danfoss AK2-SC 255, Справочное руководство, Страница: 48 / 206

Результаты поиска

Содержание AK2-SC 255

Отзывы: