manualshive.com logo in svg

Danfoss AK2-SC 255, Справочное руководство, Страница: 118 / 206

Поделиться
Скачать
Danfoss AK2-SC 255 Скачать руководство пользователя страница 118

RS.8D.M1.22

AK2-SC 255 Reference Manual

117

question](List box: 15, 20, or 30 minutes)  The window
width is set to 15, 20, or 30 minutes.  Every minute, the
window “slides” forward so that it always contains the
most recent period of time.  Each minute the accumu-
lated KW during that minute is recorded.

Normal load nn HRS

[Emergency generator control](0 to 99999)  Enter the
upper demand limit you do not wish to exceed for the
given hour of the day under normal operating condi-
tions (when using normal power). There is one field for
each hour of the day, from 00 to 23.

 This screen

has two pages in order to list all the hours of the day.

Meter setup, demand
limiting, continued (p3) Page down after entering normal load for every hour to finish configuration of the

meter. The page looks like this:

The fields in the screen are these:

Maximum emergency load [Demand limiting only](0 to 99999)  Enter the upper

demand limit that you do not wish to exceed when the
emergency generator is running.

Start shedding at

[Demand limiting only](0 to 100)  Enter the percent of
maximum load at which you want to start shedding
loads.

Start restoring at

[Demand limiting only](10 to 80)  Enter the percent of
maximum load at which you want to start restoring
loads which have been shed.

Enable coupling switch

[Demand limiting only](List box: Yes, No)  In installa-
tions where there are two transformers and/or two
emergency generators, a coupling switch can be used
to connect both loads to one source in case the other
source fails.

Number of normal steps

[Demand limiting only](0 to 10)  The number of steps
(levels) which you will allow to be shed under normal
conditions.

Num of emergency steps

[Demand limiting only](0 to 10)  The number of steps

Содержание AK2-SC 255















































































































































































































Отзывы:

Нет отзывов