Danfoss AK2-SC 255 Скачать руководство пользователя страница 172 | Manualshive

Страница: 172 / 206

Danfoss AK2-SC 255 Скачать руководство пользователя страница 172

RS.8D.M1.22

AK2-SC 255 Reference Manual

171

ture. For fixtures with a KVQ electronic evaporator
pressure regulating valve, Sensor failure can
indicate a problem with the NTC sensor in the valve
actuator.

When in Sensor failure status, an AKV valve will
operate at the mean percentage used during its most
recent period in Normal operation status. A KVQ
valve will open fully in sensor failure mode.

To determine which sensor has failed, go to the
alarms screen.

Service shutdown;

The Smart Case Controller has been shut down using
the service screen, either for case cleaning or other
service.

The screen at left below is the second page of an evaporator status screen.

Evaporator Settings
(Smart Case Control)

If you select the settings icon (second from the left on the menu bar at the bottom of
any evaporator screen), an evaporator settings screen like the one at right above
appears. To the right in the body of the screen are fields related to defrost.

Terminate:

The termination set point.

Coord:

If “Yes,” then defrost for all fixtures in this group is

coordinated.

Drip Down:

The time in seconds allowed after defrost for the

fixture to drain before refrigeration begins.

Fan Delay:

The time in minutes after defrost during which case

«
...
170
171
172
173
174
...
»

Содержание AK2-SC 255















































































































































































































Отзывы:

Нет отзывов