manualshive.com logo in svg

Danfoss AK2-SC 255, Справочное руководство, Страница: 5 / 206

Поделиться
Скачать
Danfoss AK2-SC 255 Скачать руководство пользователя страница 5

 

4

AK2-SC 255 Reference Manual

RS.8D.M1.22

Table of Contents

PART ONE

Configuration

1.1    Initial Configuration ........................................................................................................11 - 12

Introduction

..................................................................................................................................... 11

Battery

..................................................................................................................................... 11

Authorization codes .............................................................................................................................. 11 - 12
Using Menus

..................................................................................................................................... 12

Selection of units and languages ................................................................................................................. 12

1.2    Configuring Refrigeration ............................................................................................. 13 - 63

Starting with a partially configured AK2-SC 255 ........................................................................................ 13
Starting with a completely un-configured AK2-SC 255 .............................................................................. 14
Navigation and making changes .................................................................................................................. 14
Entering numerals ..................................................................................................................................... 14
Entering labels

..................................................................................................................................... 14

Constrained fields

.............................................................................................................................. 14 - 15

Configuring Rack Info .......................................................................................................................... 15 - 16

Adding a rack ..................................................................................................................................... 16

Configuring Suction Info ...................................................................................................................... 16 - 19

Configuring two-stage systems ...................................................................................................... 19 - 20

Configuring compressors ...................................................................................................................... 20 - 22

Compressor oil and safety information ........................................................................................... 22 - 23
Neutral Zone control ............................................................................................................................. 23
Compressor capacity staging patterns ........................................................................................... 24 - 25

Configuring Evaporators ...................................................................................................................... 25 - 31

Case lights button .................................................................................................................................. 27
Configuring AK2-SC 255 refrigeration circuits ..................................................................................... 28

Configuring defrost 32 - 33
Configuring evaporators ....................................................................................................................... 33 - 34
Configuring condensers ........................................................................................................................ 34 - 46

Aircooled condensers ..................................................................................................................... 35 - 42

Split condenser control ............................................................................................................. 39 - 40
Reaction zone and time ................................................................................................................... 40

Enviroguard systems ...................................................................................................................... 41 - 42
Evaporative condensers ................................................................................................................. 42 - 47

Pump, louver, and sump schedules ........................................................................................... 44 - 45
Inverter settings; freeze protection; dump valve ...................................................................... 45 - 46
Dump schedules ....................................................................................................................... 46 - 47

Receiver configuration ................................................................................................................................ 47
Heat reclaim configuration ................................................................................................................... 47 - 49
Refrigeration alarms configuration ....................................................................................................... 49 - 50
Board & Points configuration ...................................................................................................................... 50

Navigation

..................................................................................................................................... 51

Board & Points, relay outputs (digital outputs) .............................................................................. 51 - 52
Board & Points, sensor inputs (analog inputs) ............................................................................... 52 - 54
Board & Points, on-off inputs (digital inputs) ................................................................................. 54 - 55

Содержание AK2-SC 255















































































































































































































Отзывы:

Нет отзывов