Daikin Intelligent Touch Manager DCM601A71 Скачать руководство пользователя страница 39

Страница: 39 / 309

User’s Manual EM11A017

DCM601A71 intelligent Touch Manager

(6)

Group monitoring icon

A Error detection

Reports error when any of the following faults is detected.

(Red)

Flashing indicator: System error

Text: System error occurred. Touch this icon to check and restore.

(Yellow)

Flashing indicator: Unit/Limit Error

Text: Error occurred. Touch this icon to check.

(Blue)

Lit indicator: Communication error

B Emergency Stop

Reports emergency stop.

Emergency Stop

Text: Emergency stop occurred. Touch this icon to release.

Waiting for Release

Text: Emergency stop occurred. Touch this icon to release.

* A balloon is displayed when the target unit entered into waiting for release status

automatically, without the icon being touched even once. The balloon is not displayed if

the target unit was put into waiting for release status manually, by touching the icon.

OFF

C Energy Save

Displays the Energy Save status.

Enabled

Suspended

Under Control

(7)

Time

Displays the current time.

(8)

Area hierarchy indicator

Displays the hierarchical level of the currently displayed area.

(9)

Top, Down, and Up

buttons

Top

button: Displays the area and management points at the Top.

Down

button: Moves into the selected area and displays the areas and management points there.

button: Moves up one hierarchical level from that of the currently displayed area and displays

the areas and management points there.

(10)

List

switch button

Toggles the Standard View screen between Icon View and List View.

Содержание Intelligent Touch Manager DCM601A71






















































































































































































































































































































Результаты поиска

Содержание Intelligent Touch Manager DCM601A71

Отзывы:

Похожие инструкции для Intelligent Touch Manager DCM601A71

Бренды по названию

Популярные бренды

Daikin Intelligent Touch Manager DCM601A71, Руководство пользователя

Результаты поиска

Содержание Intelligent Touch Manager DCM601A71

Отзывы:

Похожие инструкции для Intelligent Touch Manager DCM601A71

Бренды по названию

Популярные бренды