Daikin Intelligent Touch Manager DCM601A71 Скачать руководство пользователя страница 212

Страница: 212 / 309

User’s Manual EM11A017

DCM601A71 intelligent Touch Manager

211

(10)

4. Touch the

Modify

button

(10)

and display the Screen Management screen.

(11)

(12)

(11)

is the list of Registered Screens while

(12)

is the list of Screens that can be registered.

Selecting a screen from

(12)

and touching the Add button registers the screen. You can only

Selecting a registered screen from

(11)

and touching the Remove button cancels its registration.

When finished, touch the OK button to save the settings and return to the User Setup screen.

Touching the OK button on the User Setup screen saves the settings and registers the Web

user.

•

Setting up Managed Area and Screen Management is unnecessary for Managers.

•

The user name and the password cannot contain special characters.

NOTE

Содержание Intelligent Touch Manager DCM601A71






















































































































































































































































































































Результаты поиска

Содержание Intelligent Touch Manager DCM601A71

Отзывы:

Похожие инструкции для Intelligent Touch Manager DCM601A71

Бренды по названию

Популярные бренды

Daikin Intelligent Touch Manager DCM601A71, Руководство пользователя

Результаты поиска

Содержание Intelligent Touch Manager DCM601A71

Отзывы:

Похожие инструкции для Intelligent Touch Manager DCM601A71

Бренды по названию

Популярные бренды