Daikin Intelligent Touch Manager DCM601A71 Скачать руководство пользователя страница 189

Страница: 189 / 309

User’s Manual EM11A017

DCM601A71 intelligent Touch Manager

188

8-3 Setting up the Emergency Stop

The iTM includes the Emergency Stop as standard function (see page 107).

The Emergency Stop is a control function envisioned primarily as a measure against fire. Based on

the emergency stop program, this function stops the management points set up as output when the

input signal set up as the emergency stop signal is received.

The Default program stops all D3 units registered as management point when an emergency stop

signal is received.

The Default program cannot be edited, except from toggling enable and disable.

If the optional Emergency Stop Control function is enabled, you can create your own emergency

stop program.

The following describes how to create and set up an emergency stop program.

1. Touch the Emergency Stop button on the Automatic Ctrl. tab of the Menu List screen and display

the Emergency Stop Control screen (see page 52).

(2)

(1)

(3)
(4)

(5)

(6)

(1)

is the list of emergency stop programs. Perform the intended operation by touching the

relevant button on the right.

(2)

Create

button

Creates a new program. You can create up to 32 emergency stop programs (including the

Default program).

(3)

Copy

button

Copies the selected program for editing.

(4)

Delete

button

Deletes the selected program.

Содержание Intelligent Touch Manager DCM601A71






















































































































































































































































































































Результаты поиска

Содержание Intelligent Touch Manager DCM601A71

Отзывы:

Похожие инструкции для Intelligent Touch Manager DCM601A71

Бренды по названию

Популярные бренды

Daikin Intelligent Touch Manager DCM601A71, Руководство пользователя

Результаты поиска

Содержание Intelligent Touch Manager DCM601A71

Отзывы:

Похожие инструкции для Intelligent Touch Manager DCM601A71

Бренды по названию

Популярные бренды