Daikin Intelligent Touch Manager DCM601A71 Скачать руководство пользователя страница 91

Страница: 91 / 309

User’s Manual EM11A017

DCM601A71 intelligent Touch Manager

(5)

Pre-Cool, Pre-Heat

radio button

Select either of the two radio buttons when using the Pre-Cool/Pre-Heat function.

Touch the Modify button and enter the setpoint in the Numerical Input dialog that appears. The

range of values you can enter is 60 to 90, in increments of 1°F.

These radio buttons are displayed only when the target is an indoor unit or area.

When Pre-Cool/Pre-Heat function is set up, the following confirmation dialog will appear as the

operation mode and setpoint set up in the A/C tab of the Events screen will be disabled. Touch

the Yes button to commit the setting.

•

Pre-cool/Pre-heat function is a function that starts the air conditioners earlier than the time

set up in the schedule to make the room temperature reach the setpoint at the set time.

The function calculates the time to automatically start the air conditioners from the suction

temperature and setpoint. The start time is adjusted accordingly as the function learns

from repeated use.

•

When Pre-Cool/Pre-Heat is set up for an area, the operation mode, the setpoint set up in

the Pre-Cool/Pre-Heat settings, and the order to start are sent to the management points

in the area at the set time. Be sure to exclude management points you do not want to

operate at set times or management points you do not want to modify their operation mode

or setpoint from the area.

•

Pre-Cool/Pre-Heat is not possible if the Setback function is being used.

NOTE

Restrictions for use of the pre-cool/heat function

Please note the following restrictions when using the pre-cool/heat function.

The pre-cool/heat function is executed according to the settings as of 0:00 on the day of execution.

Therefore, if you scheduled pre-cool/heat on the day intended for execution, the schedule will not

be executed as intended but the normal schedule will be executed on the day.

To execute pre-cool/heat as intended, make the settings before the day of execution.

•

When changing the settings

The changed settings become effective at 0:00 of the next day. Even if you change or delete

the schedule on the day of execution, the schedule identified at 0:00 will be executed.

Содержание Intelligent Touch Manager DCM601A71






















































































































































































































































































































Результаты поиска

Содержание Intelligent Touch Manager DCM601A71

Отзывы:

Похожие инструкции для Intelligent Touch Manager DCM601A71

Бренды по названию

Популярные бренды

Daikin Intelligent Touch Manager DCM601A71, Руководство пользователя

Результаты поиска

Содержание Intelligent Touch Manager DCM601A71

Отзывы:

Похожие инструкции для Intelligent Touch Manager DCM601A71

Бренды по названию

Популярные бренды