Daikin Intelligent Touch Manager DCM601A71 Скачать руководство пользователя страница 95

Страница: 95 / 309

User’s Manual EM11A017

DCM601A71 intelligent Touch Manager

•

Setpoint shift is a function that allows you to set up the setpoint with respect to the current

setpoint.

“Decrease the temperature settings” increases the setpoint for Cool mode, while for Heat

mode, it decreases the setpoint by the specified shift amount.

“Increase the temperature settings” decreases the setpoint for Cool mode, while for Heat

mode, it increases the setpoint by the specified shift amount.

•

Setpoint shift does not work when the operation mode is Fan, Automatic or Dry.

NOTE

(3)

Fan Speed setup

area

Sets up the fan speed.

Touching the button increases the fan speed by one level while touching the button

decreases the fan speed by one level.

The fan speed you can set depends on the target.

(4)

Timer Extension setup

area

Sets up the function that prevents failure to turn off the indoor unit.

Select whether to enable (On) or disable (Off) the function using the combo box.

(5)

Setpoint Restriction setup field

Sets up the setpoint restriction.

Respectively enable or disable the setpoint restrictions for cooling and heating using the combo

boxes.

Touch the respective Modify buttons and enter the maximum and minimum values in the

Numerical Input dialog that appears.

The range of values you can enter is the same as that for the Setpoint

(2)

but the entered values

should be such that they do not invert the upper and lower limits.

This field is not displayed when the Setpoint Restriction function is disabled for the target indoor

unit’s management point.

(6)

button

Saves the edit and closes the screen.

(7)

Cancel

button

Cancels the edit and closes the screen.

Содержание Intelligent Touch Manager DCM601A71






















































































































































































































































































































Результаты поиска

Содержание Intelligent Touch Manager DCM601A71

Отзывы:

Похожие инструкции для Intelligent Touch Manager DCM601A71

Бренды по названию

Популярные бренды

Daikin Intelligent Touch Manager DCM601A71, Руководство пользователя

Результаты поиска

Содержание Intelligent Touch Manager DCM601A71

Отзывы:

Похожие инструкции для Intelligent Touch Manager DCM601A71

Бренды по названию

Популярные бренды