Daikin Intelligent Touch Manager DCM601A71 Скачать руководство пользователя страница 121

Страница: 121 / 309

User’s Manual EM11A017

DCM601A71 intelligent Touch Manager

120

Saving and loading the area data CSV file

You can save the area settings in a USB memory as a CSV file (AreaData.csv). You can also load a

CSV file from a USB memory. Make sure the file is named “AreaDate.csv” as it is the only readable

fail name.

(18)
(19)

1. To save, connect a USB memory to the iTM unit and touch the

Save

button

(18)

on the Area

Setup screen. A confirmation dialog with the message “Do you want to save area data in CVS

format? Max Time : 15 sc” will appear. Touch the Yes button to save. When successfully saved,

the message “File has been saved.” will appear.

To load, connect the USB memory with the CSV file file in the iTM unit and touch the

Load

button

(19)

on the Area Setup screen. A confirmation dialog with the message “Loaded data will delete

existing data. Max Time : 15 sc” will appear. Touching the Yes button will start loading the data.

When the CSV file to load is corrupt, an error screen is displayed. Correct the errors sequentially

from the top.

The format of the CSV file used for saving and loading Area Data is as follows.

[File version]

@S:AREA-INFO

A, [Area ID], [Area name] ,[Detailed information],[Starting Interval.] ,[Stopping Interval.],[Icon ID]

, A, [Area ID], [Area name] ,[Detailed information] ,[Starting Interval.] ,[Stopping Interval.] ,[Icon ID]

, , P, [Management point ID]

, P, [Management point ID]

• • •

@E:AREA-INFO

@S:PNT-INFO

[Management point ID], [Management point name], [Management point’s detailed information], [Management point type],[Icon ID]

• • •

@E:PNT-INFO

(1) Area information block

(2) Management point information block

Содержание Intelligent Touch Manager DCM601A71






















































































































































































































































































































Результаты поиска

Содержание Intelligent Touch Manager DCM601A71

Отзывы:

Похожие инструкции для Intelligent Touch Manager DCM601A71

Бренды по названию

Популярные бренды

Daikin Intelligent Touch Manager DCM601A71, Руководство пользователя

Результаты поиска

Содержание Intelligent Touch Manager DCM601A71

Отзывы:

Похожие инструкции для Intelligent Touch Manager DCM601A71

Бренды по названию

Популярные бренды