Daikin Intelligent Touch Manager DCM601A71 Скачать руководство пользователя страница 80

Страница: 80 / 309

User’s Manual EM11A017

DCM601A71 intelligent Touch Manager

•

Weekly Pattern Tab (Schedule Edit Screen)

This screen is displayed when you touch the Weekly Pattern tab on the Schedule Edit screen.

It allows you to set up a weekly schedule.

(1)

(2)

(3)
(4)

(5)

(6)

(8)

(7)

(1)

Day of the week

radio button

Selects the day of the week to edit.

(2)

Schedule Settings

view area

Displays the schedule set to each day of the week.

(3)

Copy

button

Displays the Copy to Selection screen for selecting the destination, to which the schedule set for

the day of the week, selected with the radio button, will be copied.

(4)

Delete

button

Deletes the schedule set to the day of the week selected with radio button. Touching the button

displays a deletion confirmation dialog.

(5)

Edit

button

Displays the Event List screen that allows you to edit the schedule set up for the day of the week

selected with the radio button.

(6)

Legend

view area

Displays legends available in the Schedule Settings view area.

SB Low and SB High are displayed only when the optional setback function is enabled.

(7)

button

Saves the edit and closes the screen.

(8)

Cancel

button

Cancels the edit and closes the screen. Touching the button displays a confirmation dialog.

Содержание Intelligent Touch Manager DCM601A71






















































































































































































































































































































Результаты поиска

Содержание Intelligent Touch Manager DCM601A71

Отзывы:

Похожие инструкции для Intelligent Touch Manager DCM601A71

Бренды по названию

Популярные бренды

Daikin Intelligent Touch Manager DCM601A71, Руководство пользователя

Результаты поиска

Содержание Intelligent Touch Manager DCM601A71

Отзывы:

Похожие инструкции для Intelligent Touch Manager DCM601A71

Бренды по названию

Популярные бренды