D-Link DGS-3224TGR - Switch Скачать руководство пользователя

Страница: 46 / 160

DGS-3224TGR Gigabit Ethernet Switch User’s Guide

Subnet Mask

The address mask that controls subnetting on your TCP/IP network.

Default Gateway

The IP address of the device—usually a router—that handles connections to other
subnets and/or other TCP/IP networks.

VLAN Name

The VLAN name. The switch includes a pre-configured VLAN named “default.”

Name

A user-assigned name for the switch.

Location

A user-assigned description for the physical location of the switch.

Contact

Name of the person to contact should there be any problems or questions with the
system. You may also want to include a phone number or extension.

State

This allows you to enable or disable the IP interface.

Serial Port Settings

Figure 6- 3. Serial Port Settings window

The following fields can be set:

Parameter

Description

Baud Rate

Determines the serial port bit rate that will be used the next time the switch is restarted.
Available speeds are

9600

19,200

38,400

, and

115,200

bits per second. The default

setting is

9600

Auto Logout

This setting for the restart of the console is

2 mins

5 mins

10 mins

15 mins

, or

Never

Содержание DGS-3224TGR - Switch

































































































































































Результаты поиска

Содержание DGS-3224TGR - Switch

Отзывы:

Похожие инструкции для DGS-3224TGR - Switch

Бренды по названию

Популярные бренды

D-Link DGS-3224TGR - Switch, Руководство пользователя

Результаты поиска

Содержание DGS-3224TGR - Switch

Отзывы:

Похожие инструкции для DGS-3224TGR - Switch

Бренды по названию

Популярные бренды