D-Link DGS-3224TGR - Switch Скачать руководство пользователя

Страница: 130 / 160

DGS-3224TGR Gigabit Ethernet Switch User’s Guide

118

protocol is 22.

Authentication Method

Specify the methods of user authentication supported by
server.

Key Re-Exchange Timeout (minute)

Specify how many minutes the parties must process key re-
exchange.

Encryption

Specify the algorithm to use for encryption supported by
server.

3DES: Use 3DES encryption. Blowfish: Use Blowfish
encryption.

Data Integrity

Specify the desired MAC algorithm to use for the data integrity
verification.

SHA-1: Use the hmac-sha1 MAC. MD5: Use the hmac-md5
MAC.

Public Key

Specify the algorithm to use for the public key.

DSA: Use the DSA algorithm. RSA: Use the RSA algorithm.

SSH Account Configuration

Figure 6- 127. SSH Account Configuration window

Click

New

to open the

SSH Account Configuration – Add

window:

Figure 6- 128. SSH Account Configuration – Add window

Содержание DGS-3224TGR - Switch

































































































































































Результаты поиска

Содержание DGS-3224TGR - Switch

Отзывы:

Похожие инструкции для DGS-3224TGR - Switch

Бренды по названию

Популярные бренды

D-Link DGS-3224TGR - Switch, Руководство пользователя

Результаты поиска

Содержание DGS-3224TGR - Switch

Отзывы:

Похожие инструкции для DGS-3224TGR - Switch

Бренды по названию

Популярные бренды