D-Link DGS-3224TGR - Switch Скачать руководство пользователя

Страница: 146 / 160

DGS-3224TGR Gigabit Ethernet Switch User’s Guide

134

Group

Add to group

- add a candidate to a group. Clicking this option will reveal the following screen for the user to enter a

password for authentication from the Candidate Switch before being added to the SIM group. Click

to enter the

password or

Cancel

to exit the window.

Figure 7- 17. Input password window

Remove from Group

- remove an MS from the group.

Device

Configure

- will open the web manager for the specific device.

View

Refresh

- update the views with the latest status.

Topology

- display the Topology view.

Help

About

- Will display the SIM information, including the current SIM version.

NOTE:

Upon this firmware release, some functions of the SIM can only be

configured through the Command Line Interface. See the

DGS-3224TGR

Command Line Interface Reference Manual

for more information on

SIM and its configurations.

Содержание DGS-3224TGR - Switch

































































































































































Результаты поиска

Содержание DGS-3224TGR - Switch

Отзывы:

Похожие инструкции для DGS-3224TGR - Switch

Бренды по названию

Популярные бренды

D-Link DGS-3224TGR - Switch, Руководство пользователя

Результаты поиска

Содержание DGS-3224TGR - Switch

Отзывы:

Похожие инструкции для DGS-3224TGR - Switch

Бренды по названию

Популярные бренды