D-Link DGS-3224TGR - Switch Скачать руководство пользователя | Manualshive

Страница: 105 / 160

background image

DGS-3224TGR Gigabit Ethernet Switch User’s Guide

93

Type

Select from

Static

or

LACP

(Link Aggregation Control Protocol).

Master Port <

1

>

The Master port of link aggregation group.

Status <

Disabled

>

This field can be toggled between

Enabled

and

Disabled

. This is used to turn a link

aggregation group on or off. This is useful for diagnostics, to quickly isolate a
bandwidth intensive network device or to have an absolute backup link aggregation
group that is not under automatic control.

Port Member

Allows the specification of the ports that will make up the link aggregation group.

LACP Port Settings

LACP supports the automatic creation of link aggregation by exchanging LACP packets between LAN ports. LACP
packets are exchanged only between ports in passive and active modes. Both the passive and active modes allow LACP to
negotiate between LAN ports to determine if they can form a link aggregation.

•

Passive – LACP mode that places a port into a passive negotiating state, in which the port responds to LACP
packets it receives but does not initiate LACP negotiation. This is the default.

•

Active – LACP mode that places a port into an active negotiating state, in which the port initiates negotiations with
other ports by sending LACP packets.

LAN ports can form a trunk group when they are in different LACP modes as long as the modes are compatible. For
example:

•

A LAN port in active mode can form a trunk group successfully with another LAN port that is in active mode.

•

A LAN port in active mode can form a trunk group with another LAN port in passive mode.

A LAN port in passive mode cannot form a trunk with another LAN port that is also in passive mode, because neither port
will initiate negotiation.

«
...
103
104
105
106
107
...
»

Содержание DGS-3224TGR - Switch

































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DGS-3224TGR - Switch

Crouse-Hinds CEAG KO

Бренд: Cooper Страницы: 12

Бренд: Linksys Страницы: 3

Бренд: Edge-Core Страницы: 9

SET-2000 Oil/Sludge

Бренд: Labkotec Страницы: 15

Бренд: FS Страницы: 43

Бренд: Milestone pro Страницы: 32

Enova DGX 100 Series

Бренд: AMX Страницы: 2

Бренд: Emulex Страницы: 75

Бренд: Generac Power Systems Страницы: 2

OSD2251P Series

Бренд: Optical Systems Design Страницы: 48

Бренд: Intellinet Страницы: 12

Бренд: Woxcon Страницы: 51

Allen-Bradley Guardmaster 440G-LZ

Бренд: Rockwell Automation Страницы: 40

Бренд: LogiLink Страницы: 3

Бренд: QNAP Страницы: 30

Бренд: ZLINK Страницы: 44

Бренд: N-Tron Страницы: 152

Бренд: NETGEAR Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды