D-Link DGS-3224TGR - Switch Скачать руководство пользователя | Manualshive

Страница: 137 / 160

background image

DGS-3224TGR Gigabit Ethernet Switch User’s Guide

125

Figure 7- 1. SIM Settings window (disabled)

Change the

SIM State

to

Enabled

using the pull-down menu and click

Apply

. The window will then refresh and the

SIM

Settings

window will look like this:

Figure 7- 2. SIM Settings window (enabled)

The following parameters can be set:

Parameters Description

SIM State

Use the pull-down menu to either enable or disable the SIM state on the Switch.

Dis-

abled

will render all SIM functions on the Switch inoperable.

Role State

Use the pull-down menu to change the SIM role of the Switch. The two choices are:

Candidate

- A Candidate Switch (CaS) is not the member of a SIM group but is

connected to a Commander Switch. This is the default setting for the SIM role of the
DGS-3224TGR.

Commander

- Choosing this parameter will make the Switch a Commander Switch

(CS). The user may join other Switches to this Switch, over Ethernet, to be part of its
SIM group. Choosing this option will also enable the Switch to be configured for SIM.

Discovery Interval

The user may set the discovery protocol interval, in seconds, that the Switch will send
out discovery packets. Returning information to a Commander Switch will include
information about other Switches connected to it. (Ex. MS, CaS). The user may set
the Discovery Interval from

30

to

90

seconds.

«
...
135
136
137
138
139
...
»

Содержание DGS-3224TGR - Switch

































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DGS-3224TGR - Switch

Бренд: D-Link Страницы: 2

Бренд: JB Systems Light Страницы: 15

Бренд: Magnetrol Страницы: 28

Бренд: Jasco Страницы: 2

2X2 VGA SWITCHER

Бренд: Gefen Страницы: 12

Бренд: Hama Страницы: 10

Бренд: StarTech.com Страницы: 2

Бренд: Niles Страницы: 7

Бренд: Lindy Страницы: 2

Бренд: Taiden Страницы: 21

Бренд: Inter-m Страницы: 12

Бренд: SMC Networks Страницы: 6

N.JGS516PE-100EUS

Бренд: Duxbury Networking Страницы: 4

Бренд: H3C Страницы: 38

PROFINET 4-port

Бренд: Helmholz Страницы: 20

Бренд: Witura Страницы: 12

Бренд: Campbell Страницы: 10

ConferenceHub TA-6500

Бренд: TeleAdapt Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды