D-Link DGS-3224TGR - Switch Скачать руководство пользователя страница 153

Страница: 153 / 160

DGS-3224TGR Gigabit Ethernet Switch User’s Guide

141

TCP/IP

– A layered set of communications protocols providing Telnet terminal emulation, FTP file transfer, and other

services for communication among a wide range of computer equipment.

Telnet

– A TCP/IP application protocol that provides virtual terminal service, letting a user log in to another computer

system and access a host as if the user were connected directly to the host.

TFTP

– Trivial File Transfer Protocol. Allows you to transfer files (such as software upgrades) from a remote device

using your switch’s local management capabilities.

UDP

– User Datagram Protocol. An Internet standard protocol that allows an application program on one device to

send a datagram to an application program on another device.

VLAN

– Virtual LAN. A group of location- and topology-independent devices that communicate as if they are on a

common physical LAN.

VLT

– Virtual LAN Trunk. A Switch-to-Switch link which carries traffic for all the VLANs on each Switch.

VT100

– A type of terminal that uses ASCII characters. VT100 screens have a text-based appearance.

Содержание DGS-3224TGR - Switch

































































































































































Результаты поиска

Содержание DGS-3224TGR - Switch

Отзывы:

Бренды по названию

Популярные бренды

D-Link DGS-3224TGR - Switch, Руководство пользователя

Результаты поиска

Содержание DGS-3224TGR - Switch

Отзывы:

Бренды по названию

Популярные бренды