D-Link DGS-3224TGR - Switch Скачать руководство пользователя | Manualshive

Страница: 60 / 160

background image

DGS-3224TGR Gigabit Ethernet Switch User’s Guide

48

Management Station IP Addresses

Management stations are computers on the network that will be used to manage the switch. You can limit the number of
possible management stations by entering up to three IP addresses. If the three IP Address

fields contain all zeros (“0”),

then any station with any IP address can access the switch to manage and configure it. If there is one or more IP addresses
entered in the

IP Address

fields, then only stations with the IP addresses entered will be allowed to access the switch to

manage or configure it.

Figure 6- 23. Management Station IP Addresses window

Switch Utilities

TFTP Services

Trivial File Transfer Protocol (TFTP) services allow the switch firmware to be upgraded by downloading a new firmware
file from a TFTP server to the switch. A configuration file can also be loaded into the switch, and switch settings can be
saved to a TFTP server. In addition, the switch’s history log can be uploaded to a TFTP server.

Please note that TFTP server software must be running on the management station for the TFTP services listed here to
work.

Download Firmware from TFTP Server

Figure 6- 24. Download Firmware from TFTP Server window

Enter the IP address of the TFTP server in the Server IP Address field and the complete path and file name of the firmware
file for the switch in the Path/Filename field. Click

Download

to initiate the file transfer.

«
...
58
59
60
61
62
...
»

Содержание DGS-3224TGR - Switch

































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DGS-3224TGR - Switch

Бренд: D-Link Страницы: 2

S5500-SI Series

Бренд: H3C Страницы: 130

S5500-EI series

Бренд: H3C Страницы: 19

S5500-EI series

Бренд: H3C Страницы: 91

S5500-EI series

Бренд: H3C Страницы: 24

S5500-EI series

Бренд: H3C Страницы: 69

S5120-SI Series

Бренд: H3C Страницы: 4

S5120-SI Series

Бренд: H3C Страницы: 209

S5120-SI Series

Бренд: H3C Страницы: 70

S5120-EI Series

Бренд: H3C Страницы: 32

Бренд: H3C Страницы: 83

Бренд: H3C Страницы: 26

S5500-SI Series

Бренд: H3C Страницы: 6

PARAGON II Series

Бренд: Raritan Страницы: 1

Paragon Manager

Бренд: Raritan Страницы: 117

Бренд: Raritan Страницы: 4

Бренд: ATZ Страницы: 8

EXT-DVIKVM-441DL

Бренд: Gefen Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды