D-Link DGS-3224TGR - Switch Скачать руководство пользователя

Страница: 15 / 160

DGS-3224TGR Gigabit Ethernet Switch User’s Guide

Unpacking and Setup

This chapter provides unpacking and setup information for the switch.

Unpacking

Open the shipping carton of the switch and carefully unpack its contents. The carton should contain the following items:

•

A DGS-3224TGR 24-Port Gigabit Layer 2 Ethernet switch

•

A mounting kit: 2 mounting brackets and screws

•

Four rubber feet with adhesive backing

•

One or two AC power cords

•

A printed QIG

•

A printed User’s Guide

•

D-View 5.1 demo CD-ROM

•

This User’s Guide with Registration Card on CD-ROM

If any item is found missing or damaged, please contact your local D-Link reseller for replacement.

Installation

Use the following guidelines when choosing a place to install the switch:

•

The surface must support at least 4 kg.

•

The power outlet should be within 1.82 meters (6 feet) of the device.

•

Visually inspect the power cord and see that it is secured to the AC power connector.

•

Make sure that there is proper heat dissipation from and adequate ventilation around the switch. Do not place heavy
objects on the switch.

Содержание DGS-3224TGR - Switch

































































































































































Результаты поиска

Содержание DGS-3224TGR - Switch

Отзывы:

Похожие инструкции для DGS-3224TGR - Switch

Бренды по названию

Популярные бренды

D-Link DGS-3224TGR - Switch, Руководство пользователя

Результаты поиска

Содержание DGS-3224TGR - Switch

Отзывы:

Похожие инструкции для DGS-3224TGR - Switch

Бренды по названию

Популярные бренды