D-Link DGS-3224TGR - Switch Скачать руководство пользователя | Manualshive

Страница: 20 / 160

background image

DGS-3224TGR Gigabit Ethernet Switch User’s Guide

8

Side Panels

The right side panel of the switch contains two system fans (see the top part of the diagram below). The left side panel
contains heat vents.

Figure 3-3. Side panel views of the Switch

•

The system

fans are used to dissipate heat. The sides of the system also provide heat vents to serve the same purpose.

Do not block these openings, and leave at least 6 inches of space at the rear and sides of the switch for proper
ventilation. Be reminded that without proper heat dissipation and air circulation, system components might overheat,
which could lead to system failure.

LED Indicators

The LED indicators of the switch include Power, Console, RPS, Speed, and Link/Activity. The following shows the LED
indicators for the switch along with an explanation of each indicator.

Figure 3-4. LED indicators

•

Power

– This indicator on the front panel lights solid green when the system is powered up and remains dark when the

system is not powered on.

•

Console

– This indicator blinks green when the system is booting up. It remains solid green when the system is

operating properly. The LED is solid amber when the POST fails.

•

RPS

– This indicator is lit solid amber when the external Redundant Power Supply is in operation and remains dark

when it is not in use or the main power is working normally.

•

Speed

– This row of indicators will light solid green when the connection speed is operating at 1000 Mbps. An unlit

LED indicates a connection speed of either 10 or 100 Mbps.

•

Link/Act

–

This row of indicators for the 24 copper ports light solid green when there is a secure connection (or link)

to a device on any of the ports. The LEDs blink green whenever there is reception or transmission (i.e. Activity--Act)
of data occurring on a port.

«
...
18
19
20
21
22
...
»

Содержание DGS-3224TGR - Switch

































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DGS-3224TGR - Switch

Бренд: wavin Страницы: 4

Бренд: Magnetrol Страницы: 28

Infinity IES-1881

Бренд: LevelOne Страницы: 2

Бренд: Conrad Страницы: 8

FOS-3124 SERIES

Бренд: CTS Страницы: 223

3C16710 - OfficeConnect 8/TPM Hub

Бренд: 3Com Страницы: 130

FL SWITCH SFN 16TX

Бренд: Phoenix Contact Страницы: 6

S5120-EI Series

Бренд: H3C Страницы: 29

Бренд: Linkskey Страницы: 2

Бренд: LevelOne Страницы: 76

Бренд: Black Box Страницы: 2

Бренд: NewStar Страницы: 10

Бренд: Minicom Страницы: 16

Бренд: Pilz Страницы: 20

Бренд: N-Tron Страницы: 157

Бренд: ALFAtron Страницы: 44

Бренд: Black Box Страницы: 20

Бренд: IOGear Страницы: 54

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды