D-Link DGS-3224TGR - Switch Скачать руководство пользователя | Manualshive

Страница: 66 / 160

background image

DGS-3224TGR Gigabit Ethernet Switch User’s Guide

54

Port

Select the port you want port error packet statistics for from the drop-down menu.

Interval

Select the desired setting between

2 seconds

and

60 seconds

or

Suspend

.

Clear

Clicking this button clears all statistics counters on this window.

CrcError

Counts otherwise valid frames that did not end on a byte (octet) boundary.

Undersize

The number of frames detected that are less than the minimum permitted frame size of 64
bytes and have a good CRC. Undersize frames usually indicate collision fragments, a
normal network occurrence.

Oversize

Counts packets received that were longer than 1518 octets, or if a VLAN frame 1522
octets, and less than the MAX_PKT_LEN. Internally, MAX_PKT_LEN is equal to 1522.

Fragment

The number of packets less than 64 bytes with either bad framing or an invalid CRC.
These are normally the result of collisions.

Jabber

The number of frames with lengths more than the MAX_PKT_LEN bytes. Internally,
MAX_PKT_LEN is equal to 1522.

Drop Packets

The number of frames that are dropped by this port since the last Switch reboot.

Excessive
Deferral

Counts the number of frames for which the first transmission attempt on a particular
interface was delayed because the medium was busy.

CRC Error

For 10 Mbps ports, the counter records CRC errors (FCS or alignment errors). For 100
Mbps ports, the counter records the sum of CRC errors and code errors (frames received
with rxerror signal).

Late Collision

Counts the number of times that a collision is detected later than 512 bit-times into the
transmission of a packet.

Excessive
Collision

The number of frames for which transmission failed due to excessive collisions.

Single Collision

The number of successfully transmitted frames for which transmission is inhibited by more
than one collision.

Collision

An estimate of the total number of collisions on this network segment.

Port Packet Analysis

Figure 6- 32. Port Packet Analysis window

The information is described as follows:

«
...
64
65
66
67
68
...
»

Содержание DGS-3224TGR - Switch

































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DGS-3224TGR - Switch

Бренд: Keithley Страницы: 434

DSR Series DSR1030

Бренд: Avocent Страницы: 8

EdgeSwitch 10 XP

Бренд: Ubiquiti Страницы: 13

Бренд: Zamel Страницы: 2

Бренд: ALFAtron Страницы: 15

Бренд: AETEK Страницы: 2

Бренд: SignaMax Страницы: 6

Бренд: Extron electronics Страницы: 3

Бренд: Jerguson Страницы: 16

Бренд: Clas Ohlson Страницы: 5

OpenGear DSS-8224

Бренд: Ross Страницы: 47

Бренд: PowerShield Страницы: 2

COMMANDE MURALE RTS

Бренд: SOMFY Страницы: 2

Бренд: Stahl Страницы: 28

3508-11 CenturySwitch

Бренд: METRObility Optical Systems Страницы: 20

Бренд: TRENDnet Страницы: 2

Бренд: PureLink Страницы: 12

Бренд: Shinybow USA Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды