D-Link DGS-3224TGR - Switch Скачать руководство пользователя

Страница: 63 / 160

DGS-3224TGR Gigabit Ethernet Switch User’s Guide

Parameter

Description

Server IP Address

The IP address of the TFTP server.

Path/File Name

The full file name (including path) of the setting file on the TFTP server.

Ping Test

The switch is able to test the connection with another network device using Ping.

Figure 6- 28. Ping Test window

Enter the IP address of the network device to be Pinged in the first field, select the number of test packets to be sent (three
is usually enough) in the second field, and enter a time-out value in the third field. Click

Start

to initiate the Ping program.

Содержание DGS-3224TGR - Switch

































































































































































Результаты поиска

Содержание DGS-3224TGR - Switch

Отзывы:

Похожие инструкции для DGS-3224TGR - Switch

Бренды по названию

Популярные бренды

D-Link DGS-3224TGR - Switch, Руководство пользователя

Результаты поиска

Содержание DGS-3224TGR - Switch

Отзывы:

Похожие инструкции для DGS-3224TGR - Switch

Бренды по названию

Популярные бренды