D-Link DES-3326S - Switch - Stackable Скачать руководство пользователя | Manualshive

Страница: 125 / 354

background image

DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual

Spanning Tree Commands

125

config stp

Purpose

Used to setup STP and RSTP on the switch.

Syntax

config stp {maxage <value>/hellotime
<value>/forwarddelay <value>/priority
<value>/fbpdu [enabled/disabled]/
txholdcount <1-10>/ version[rstp/stp]}

Description

This command is used to setup the
Spanning Tree Protocol (STP) for the entire
switch.

Parameters

maxage <value>

−

The maximum amount of

time (in seconds) that the switch will wait to
receive a BPDU packet before reconfiguring
STP. The default is 20 seconds.

hellotime <value>

−

The time interval

between transmission of configuration
messages by the root device. The default is 2
seconds.

forwarddelay <value>

−

The maximum

amount of time (in seconds) that the root
device will wait before changing states. The
default is 15 seconds.

priority <value>

−

A numerical value

between 0 and 65535 that is used in
determining the root device, root port, and
designated port. The device with the highest
priority becomes the root device. The lower
the numerical value, the higher the priority.
The default is 32,768.

fbpdu [enabled/disabled]

−

Allows the

forwarding of STP BPDU packets from other

«
...
123
124
125
126
127
...
»

Содержание DES-3326S - Switch - Stackable



































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DES-3326S - Switch - Stackable

Бренд: Barksdale Страницы: 5

GuardSwitch 300 Series

Бренд: GE Страницы: 4

DynaGST/2402G GEP-33224T-1

Бренд: UNICOM Страницы: 1

Cleveland Controls RSS-498-013

Бренд: UNICONTROL Electronic Страницы: 2

Бренд: Server Technology Страницы: 12

EtherDevice EDS-4009 Series

Бренд: Moxa Technologies Страницы: 18

Бренд: TP-Link Страницы: 2

Pow-R-Line SPX0361126

Бренд: Eaton Страницы: 584

Бренд: Metrix Страницы: 12

Бренд: Nobile Страницы: 2

Nexoos 370 Series

Бренд: Soyntec Страницы: 7

DigiTOOLS VS-41USB

Бренд: Kramer Страницы: 8

TK-205K - PS/2 KVM Switch

Бренд: TRENDnet Страницы: 11

INTEGRAL Series

Бренд: DAS AUDIO Страницы: 45

Бренд: NegoRack Страницы: 41

Бренд: Leaksafe Solutions Страницы: 12

Smatrix Wave Plus Uahome Module R-167

Бренд: Uponor Страницы: 48

Бренд: DANLERS Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды