D-Link DES-3326S - Switch - Stackable Скачать руководство пользователя | Manualshive

Страница: 37 / 354

background image

DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual

Basic Switch Commands

37

enable telnet

Purpose

Used to enable communication with and
management of the switch using the Telnet
protocol.

Syntax

enable telnet <tcp_port_number>

Description

This command is used to enable the Telnet
protocol on the switch. The user can specify
the TCP or UDP port number the switch will
use to listen for Telnet requests.

Parameters

<tcp_port_number>

−

The TCP port number.

TCP ports are numbered between 1 and
65535. The

“

well-known

”

TCP port for the

Telnet protocol is 23.

Restrictions

Only administrator-level users can issue
this command.

Example Usage:

To enable Telnet and configure port number:

DES-3326SR:4#enable telnet 23
Command: enable telnet 23

Success.

DES-3326SR:4#

«
...
35
36
37
38
39
...
»

Содержание DES-3326S - Switch - Stackable



































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DES-3326S - Switch - Stackable

DUB-H4 - Hub - USB

Бренд: D-Link Страницы: 4

Бренд: D-Link Страницы: 2

SmartSwitch 9A100

Бренд: Cabletron Systems Страницы: 52

SmartSwitch 9W006

Бренд: Cabletron Systems Страницы: 34

SmartSTACK ELS100-S24TX2M

Бренд: Cabletron Systems Страницы: 102

Бренд: Cabletron Systems Страницы: 24

SmartSwitch 9000

Бренд: Cabletron Systems Страницы: 14

Бренд: Cabletron Systems Страницы: 38

Бренд: Zigen Страницы: 40

Бренд: Zigen Страницы: 4

DMS-1250 Series

Бренд: D-Link Страницы: 38

Liquipoint FTW33

Бренд: Endress+Hauser Страницы: 48

Бренд: Minicom Страницы: 16

Бренд: Pilz Страницы: 20

Бренд: Xantech Страницы: 12

SBX 95 SE - AV Control 4

Бренд: Vivanco Страницы: 16

Бренд: MiLAN Страницы: 13

Бренд: Gigacore Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды