D-Link DES-3326S - Switch - Stackable Скачать руководство пользователя страница 44

Страница: 44 / 354

DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual

Basic Switch Commands

DES-3326SR:4#reset config
Command: reset config

Success.

DES-3326SR:4#

Purpose

Used to log in a user to the switch

’

s console.

Syntax

Description

This command is used to initiate the login
procedure. The user will be prompted for his
Username and Password.

Parameters

none.

Restrictions

none.

Example Usage:

To initiate the login procedure:

DES-3326SR:4#login
Command: login

UserName:

Содержание DES-3326S - Switch - Stackable



































































































































































































































































































































































Результаты поиска

Содержание DES-3326S - Switch - Stackable

Отзывы:

Бренды по названию

Популярные бренды

D-Link DES-3326S - Switch - Stackable, Справочное руководство по интерфейсу командной строки

Результаты поиска

Содержание DES-3326S - Switch - Stackable

Отзывы:

Бренды по названию

Популярные бренды