D-Link DES-3326S - Switch - Stackable Скачать руководство пользователя

Страница: 318 / 354

DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual

318

OSPF Configuration Commands

create ospf aggregation

Purpose

Used to configure OSPF area aggregation
settings.

Syntax

create ospf aggregation <area_id>
<network_address> lsdb_type [summary]
{advertise [enabled/disabled]}

Description

This command is used to create an OSPF
area aggregation.

Parameters

<area_id>

−

A 32-bit number in the form of

an IP address (xxx.xxx.xxx.xxx) that
uniquely identifies the OSPF area in the
OSPF domain.

<network_address>

−

The 32-bit number

in the form of an IP address that uniquely
identifies the network that corresponds to
the OSPF Area.

lsdb_type [summary]

−

The type of address

aggregation.

advertise [enabled/disabled]

−

Allows for

the advertisement trigger to be enabled or
disabled.

Restrictions

Only administrator-level users can issue
this command.

Содержание DES-3326S - Switch - Stackable



































































































































































































































































































































































Результаты поиска

Содержание DES-3326S - Switch - Stackable

Отзывы:

Похожие инструкции для DES-3326S - Switch - Stackable

Бренды по названию

Популярные бренды

D-Link DES-3326S - Switch - Stackable, Справочное руководство по интерфейсу командной строки

Результаты поиска

Содержание DES-3326S - Switch - Stackable

Отзывы:

Похожие инструкции для DES-3326S - Switch - Stackable

Бренды по названию

Популярные бренды