D-Link DES-3326S - Switch - Stackable Скачать руководство пользователя | Manualshive

Страница: 179 / 354

background image

DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual

VLAN Commands

179

config gvrp

Purpose

Used to configure GVRP on the switch.

Syntax

config gvrp [<portlist>/all] {state
[enabled/disabled]/ingress_checking
[enabled/disabled]}

Description

This command is used to configure the
Group VLAN Registration Protocol on the
switch. You can configure ingress checking,
the sending and receiving of GVRP
information, and the Port VLAN ID (PVID).

Parameters

<portlist>

−

A range of ports for which you

want ingress checking. The port list is
specified by listing the lowest switch
number and the beginning port number on
that switch, separated by a colon. Then
highest switch number, and the highest
port number of the range (also separated by
a colon) are specified. The beginning and
end of the port list range are separated by a
dash. For example, 1:3 would specify switch
number 1, port 3. 2:4 specifies switch
number 2, port 4. 1:3-2:4 specifies all of the
ports between switch 1, port 3 and switch 2,
port 4

−

in numerical order.

all

−

Specifies all of the ports on the switch.

state [enabled/disabled]

−

Enables or

disables GVRP for ports in port list.
ingress_checking [enabled/disabled]

−

Enables or disables ingress checking for the
specified port list.

Restrictions

Only administrator-level users can issue
this command.

«
...
177
178
179
180
181
...
»

Содержание DES-3326S - Switch - Stackable



































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DES-3326S - Switch - Stackable

Бренд: IBM Страницы: 2

Бренд: ATZ Страницы: 8

EXT-DVIKVM-441DL

Бренд: Gefen Страницы: 32

Бренд: hager Страницы: 2

Бренд: Little Giant Страницы: 2

Бренд: Lantech Страницы: 24

Бренд: Cabletron Systems Страницы: 83

SmartStack STS16-20R

Бренд: Cabletron Systems Страницы: 258

Бренд: cable matters Страницы: 8

Бренд: BluStream Страницы: 4

GlobeCaster STUDIO 4000

Бренд: Global Streams Страницы: 144

TNM4000-TP36FF4X16G24P

Бренд: MRD Страницы: 38

Бренд: C&H Technologies Страницы: 28

Бренд: Edimax Страницы: 2

Бренд: H3C Страницы: 38

PROFINET 4-port

Бренд: Helmholz Страницы: 20

Бренд: odot Страницы: 15

Бренд: Videosec Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды