D-Link DES-3326S - Switch - Stackable Скачать руководство пользователя

Страница: 217 / 354

DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual

Routing Table Commands

217

Example Usage:

To add a static address 10.48.74.121 , mask 255.0.0.0 and
gateway 10.1.1.254 to the routing table:

DES-3326SR:4#create iproute 10.48.74.121/255.0.0.0 10.1.1.254 1
Command: create iproute 10.48.74.121/8 10.1.1.254 1

Success.

DES-3326SR:4#

delete iproute

Purpose

Used to delete an IP route entry from the
switch

’

s IP routing table.

Syntax

delete iproute [default/<network_address>]

Description

This command will delete an existing entry
from the switch

’

s IP routing table.

Parameters

default

−

deletes a default IP route entry.

<network_address>

−

IP address and

netmask  of  the  IP  interface  that  is  the
destination of the route.  You can specify the
address  and  mask  information  using  the
traditional

format

(for

example,

10.1.2.3/255.0.0.0 or in CIDR format,
10.1.2.3/16).

Restrictions

Only administrator-level users can issue this
command.

Содержание DES-3326S - Switch - Stackable



































































































































































































































































































































































Результаты поиска

Содержание DES-3326S - Switch - Stackable

Отзывы:

Похожие инструкции для DES-3326S - Switch - Stackable

Бренды по названию

Популярные бренды

D-Link DES-3326S - Switch - Stackable, Справочное руководство по интерфейсу командной строки

Результаты поиска

Содержание DES-3326S - Switch - Stackable

Отзывы:

Похожие инструкции для DES-3326S - Switch - Stackable

Бренды по названию

Популярные бренды