D-Link DES-3326S - Switch - Stackable страница 47 Скачать руководство пользователя | Manualshive

Страница: 47 / 354

background image

DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual

Switch Port Commands

47

config ports

Purpose

Used to configure the switch

’

s Ethernet port

settings.

Syntax

config ports [<portlist/all>]
{speed[auto/10_half/10_full/100_half/100_hal
f/1000_full] learning [enabled/disabled] state
[enabled/disabled]}

Description

This command allows for the configuration of the
switch

’

s Ethernet ports. Only the ports listed in

the <portlist> will be affected.

Parameters

all

−

Displays all ports on the switch.

<portlist>

−

Specifies a range of ports to be

configured. The port list is specified by listing the
beginning port number and the highest port
number of the range. The beginning and end of
the port list range are separated by a dash. For
example, 3 would specify port 3. 4 specifies port
4. 3-4 specifies all of the ports between port 3
and port 4

−

in numerical order.

auto

−

Enables auto-negotiation for the specified

range of ports.

[10/100/1000]

−

Configures the speed in Mbps

for the specified range of ports. Gigabit ports are
statically set to 1000 and cannot be set to slower
speeds.

[half/full]

−

Configures the specified range of

ports as either full- or half-duplex.

learning [enabled/disabled]

−

Enables or disables

«
...
45
46
47
48
49
...
»

Содержание DES-3326S - Switch - Stackable



































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DES-3326S - Switch - Stackable

Бренд: JDS Uniphase Страницы: 40

Бренд: Campbell Hausfeld Страницы: 12

Бренд: Patton electronics Страницы: 104

Бренд: I-Tech Страницы: 27

Бренд: Black Box Страницы: 26

Allen-Bradley 194U Series

Бренд: Rockwell Automation Страницы: 2

Бренд: Extron electronics Страницы: 137

JTECH-4KPIP0401

Бренд: J-Tech Digital Страницы: 10

Бренд: Accton Technology Страницы: 7

Бренд: Icy Box Страницы: 12

Бренд: LevelOne Страницы: 15

Бренд: 3Com Страницы: 62

Бренд: Good Way Страницы: 13

kontron KSwitch D3 UMP

Бренд: S&T Страницы: 36

Бренд: Anker Страницы: 16

Бренд: Ruby Tech Страницы: 2

Бренд: Smartwares Страницы: 44

SIRCO MOT PV UL

Бренд: socomec Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды