D-Link DES-3326S - Switch - Stackable страница 229 Скачать руководство пользователя | Manualshive

Страница: 229 / 354

background image

DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual

Route Redistribution Commands

229

config route redistribute dst rip

Purpose

Used to configure route redistribution from
OSPF to RIP.

Syntax

config route redistribute dist rip src
[local/static/ospf
{all/internal/external/type_1/type_2}]
{metric <value>}

Description

Route redistribution allows routers on the
network

−

that are running different routing

protocols to exchange routing information.
this is accomplished by comparing the
routes stored in the various router

’

s routing

tables  and  assigning  appropriate  metrics.
this  information  is  then  exchanged  among
the  various  routers  according  to  the
individual  routers  current  routing  protocol.
The

switch

can

redistribute

routing

information  between  the  OSPF  and  RIP
routing  protocols  to  all  routers  on  the
network  that  are  running  OSPF  or  RIP.
Routing  information  entered  into  the  Static
Routing  Table  on  the  local  switch  is  also
redistributed.

Parameters

src

−

Allows the selection of the routing

protocol on the source device.
dst

−

Allows the selection of the routing

protocol on the destination device.
<value>

−

Allows the entry of an OSPF

interface cost. This is analogous to a Hop
Count in the RIP routing protocol.

Restrictions

Only administrator-level users can issue
this command.

«
...
227
228
229
230
231
...
»

Содержание DES-3326S - Switch - Stackable



































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DES-3326S - Switch - Stackable

Бренд: D-Link Страницы: 2

Бренд: WAGO Страницы: 39

Бренд: Cole Hersee Страницы: 2

AVS-OP-1616-340

Бренд: AMX Страницы: 1

Бренд: INFLUX MEASUREMENTS Страницы: 6

Pow-R-Line SPX0361126

Бренд: Eaton Страницы: 584

Бренд: Sangamo Страницы: 2

CentreCOM GS970M Series

Бренд: Allied Telesis Страницы: 21

Бренд: FCI Страницы: 12

Digital Energy STS-400-25-3

Бренд: GE Страницы: 49

Signature ANTENNA GENIUS 8x2 v2 PLUS

Бренд: 4O3A Страницы: 57

Бренд: PABX Страницы: 46

Бренд: TESmart Страницы: 12

Бренд: C&H Technologies Страницы: 28

S5130-EI Series

Бренд: H3C Страницы: 32

Бренд: YOKOGAWA Страницы: 74

Бренд: IOGear Страницы: 40

Бренд: Grandbeing Страницы: 27

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды