Cryomech CPA289C Скачать руководство пользователя страница 61

Страница: 61 / 64

Routine Maintenance

8-3

Figure 8-1: Disconnecting the Aeroquip adsorber

Remove the nut holding the high pressure Aeroquip coupling to the front panel.

Loosen and disconnect the hose clamp that attaches the adsorber to the front
panel.

Remove the adsorber from the helium compressor package.

Check the Aeroquip couplings for oil residue.

a. If oil is present, contact Cryomech, Inc. for further assistance.

Remove the lock washer from the top Aeroquip on CP2800 and CP1100 helium
compressor packages.

10.

To install the new adsorber, reverse steps 1 through 9.

8.5 Vent excess helium from the helium compressor package

Required tools:

Quantity

Description

Comment

3/4 in open end wrench

For Aeroquip coupling

Service Aeroquip coupling

For service access port

CAUTION

Venting more than 5 psig (0.34 bar) of helium per minute will lead to improper oil migration within
the system. If this condition occurs, factory service will be required.

This procedure should only be used to vent small quantities of helium from an overcharged
system.

Make sure the service valve is closed. See Figure 8-2.

Attach the service Aeroquip coupling to the service access port.

Hold this wrench

Hose clamp

Hold this wrench

Turn this wrench

Содержание CPA289C

































































Результаты поиска

Содержание CPA289C

Отзывы:

Похожие инструкции для CPA289C

Бренды по названию

Популярные бренды

Cryomech CPA289C, Инструкция по установке и эксплуатации

Результаты поиска

Содержание CPA289C

Отзывы:

Похожие инструкции для CPA289C

Бренды по названию

Популярные бренды