Cryomech CPA289C Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 64

background image

Safety

3-5

Section 7.1.2 Startup procedure

WARNING

The system operates in a closed loop cycle at pressures higher than 200 psig (12.8 bar) and at
temperatures below 120 K.

Section 7.6 Disassembling the system for transport or storage

WARNING

Do not touch the cold end of the cold head until it has warmed to room temperature. If there is frost on
the cold head, it is too cold to touch.

3.2.4 Section 8: Routine maintenance

Section 8.3 Cold head

CAUTION

The Pulse Tube style cold heads contain no user-serviceable parts. Attempting to disassemble the cold
head will void the warranty. Contact Cryomech, Inc if the cold head needs to be returned for servicing.

CAUTION

Service to Gifford-McMahon style cold heads must be performed using Cryomech, Inc parts and the
appropriate work instructions. Contact Cryomech, Inc. before servicing the cold head.

Section 8.4 Replace the adsorber

CAUTION

At no time should the Aeroquip couplings be removed from the adsorber. Replacement can be completed
without relieving system pressure, since the adsorber is equipped with Aeroquip couplings for sealed
removal.

WARNING

The input power must be disconnected from the helium compressor package before removing any helium
compressor package panels.

Section 8.5 Vent excess helium from the helium compressor package

CAUTION

Venting more than 5 psig (0.34 bar) of helium per minute will lead to improper oil migration within the
system. If this condition occurs, factory service will be required.

«
...
13
14
15
16
17
...
»

Содержание CPA289C

































































Отзывы:

Нет отзывов

Похожие инструкции для CPA289C

Бренд: Abus Страницы: 2

Бренд: Abus Страницы: 12

Бренд: Abu Garcia Страницы: 6

Бренд: Eagle Eye Страницы: 21

Бренд: Labomed Страницы: 67

Бренд: Harken Страницы: 4

Бренд: Harken Страницы: 2

TERRA FORCE BOOM

Бренд: Hardi Страницы: 40

Бренд: Harken Страницы: 4

QuickSlide HemaPRO

Бренд: Hardy Diagnostics Страницы: 2

Бренд: Hardt Страницы: 2

Бренд: Jacto Страницы: 12

Бренд: LA Audio Страницы: 9

Бренд: Madsen Страницы: 206

Бренд: Waterpik Страницы: 2

Бренд: MÄDLER Страницы: 4

Бренд: VanGaa Lighting Страницы: 7

GPSMAP 7400 Series

Бренд: Garmin Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды