Cryomech CPA289C Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 64

background image

Specifications

5-4

High-Pressure Atmospheric Relief Valve

The helium compressor package high-pressure atmospheric relief valve is set at
420 ± 5 psig (29 ± .34 bar). At pressures above 420 psig (29 bar) the relief valve will open
automatically and relieve pressure to the atmosphere.

Internal Motor Overload Switch

An internal motor overload switch, located inside the helium compressor package module, protects
the system by sensing excessive current draw and temperature. This switch automatically resets
itself after the helium compressor package module cools to an acceptable level.

Cold Head High Pressure Relief Valve

The cold head high pressure atmospheric relief valve is set at 425 ± 5 psig (29.3 ± .34 bar). At
pressures above 425 psig (29.3 bar) the valve will open automatically and relieve pressure to the
atmosphere.

«
...
22
23
24
25
26
...
»

Содержание CPA289C

































































Отзывы:

Нет отзывов

Похожие инструкции для CPA289C

Бренд: Fender Страницы: 15

Бренд: J D Squared Страницы: 18

Бренд: Eagle Eye Страницы: 21

Бренд: Labomed Страницы: 67

Бренд: Olsen Страницы: 4

Dominator Series

Бренд: Falcon Страницы: 31

Бренд: Fakir Страницы: 22

Бренд: laerdal Страницы: 8

Бренд: LAHTI PRO Страницы: 16

Бренд: laerdal Страницы: 32

Бренд: laerdal Страницы: 32

Бренд: laerdal Страницы: 8

Бренд: PacBio Страницы: 13

Бренд: Pablo Страницы: 4

Бренд: PA Страницы: 28

Бренд: Wassermann Страницы: 24

MCX-C15 - MusicCAST Network Audio Player

Бренд: Yamaha Страницы: 65

Бренд: Yamaha Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды