Cryomech CPA289C Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 64

background image

Specifications

5-5

5.3. Description of helium compressor package

Figure 5-3: Front panel of the water cooled helium compressor package

5.3.1. Front panel interfaces

This section describes the function of the interfaces on the CPA289C helium compressor package.

1. Low Pressure Gauge

The pressure of the helium gas being returned to the helium compressor package from the cold
head.

2. High Pressure Gauge

The pressure of the helium gas being sent to the cold head from the helium compressor
package.

3. Low Pressure Aeroquip

Flex line connection for gas returning from the cold head to the suction side of the helium
compressor package.

4. High Pressure Aeroquip

Flex line connection for gas going to the cold head from the discharge side of the helium
compressor package.

5. Service Valve

Regulates the gas flow through the service access Aeroquip.

6. Service Access

Helium compressor package connection used to add or remove helium.

7. Helium Compressor Package ON Button

A mechanical button used to start the system.

8. Helium Compressor Package OFF Button

A mechanical button used to stop the system.

«
...
23
24
25
26
27
...
»

Содержание CPA289C

































































Отзывы:

Нет отзывов

Похожие инструкции для CPA289C

Бренд: Xtool Страницы: 51

Бренд: H-TEC Education Страницы: 16

Бренд: H-TEC Education Страницы: 12

Бренд: Ibiza Страницы: 21

Бренд: IBASE Technology Страницы: 67

Бренд: IBC Страницы: 8

Бренд: Ibanez Страницы: 8

Бренд: IAI Страницы: 5

Бренд: IDEAL Страницы: 12

Бренд: Landoll Страницы: 70

Бренд: Landice Страницы: 19

Бренд: Landice Страницы: 7

Бренд: M-Audio Страницы: 3

Бренд: Xtralis Страницы: 26

Бренд: Yamaha Страницы: 4

Бренд: Wacker Neuson Страницы: 120

Бренд: Yamaha Страницы: 48

Бренд: ubicquia Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды