Cryomech CPA289C Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 64

background image

Specifications

5-10

Start (Pin 15)

When Start is enabled, the compressor will enter Startup mode then Running mode. If there is an
off command coming from any input; Compressor OFF Button, Screen OFF Button, System I/O
Stop, System I/O Interlock, Modbus or SMDP stop command, or an error, the system will not start.

Outputs

Running (Pins 1-2)

When the system is in Running mode, and operating properly, the Running relay between pins 1
and 2 will closed.

High Pressure (Pins 3-4)

If the discharge pressure of the compressor package exceeds the high pressure limit the High-
Pressure relay between pins 3 and 4 will close.

High Temperature (Pins 5-6)

If the helium gas of the compressor package exceeds the high temperature limit the High
temperature relay between pins 5 and 6 will close.

Faultless (Pins 7-8)

If the system is powered on and in a running or idle state and the system is experiencing no
warnings or errors the relay between pins 7 and 8 will close.

Voltage supply

Pin 11 is +24 Vdc source referenced to the ground, pin 10. The maximum current available is 40
mA. This supply can be used to power the inputs. The supply may also be used for other purposes
provided the current limit is not exceeded.

«
...
28
29
30
31
32
...
»

Содержание CPA289C

































































Отзывы:

Нет отзывов

Похожие инструкции для CPA289C

Бренд: ParaBody Страницы: 4

WJHD309A - DIGITAL DISK RECORDER

Бренд: Panasonic Страницы: 79

Бренд: A.MENARINI Страницы: 2

Бренд: Rangevision Страницы: 28

Бренд: Handler Страницы: 25

Бренд: Wahl Страницы: 47

Бренд: Garmin Страницы: 2

Бренд: Landi Renzo Страницы: 16

Бренд: IBM Страницы: 163

Бренд: Labelmate Страницы: 61

Бренд: Labconco Страницы: 62

Бренд: MAGIC FX Страницы: 25

TRAKTOR KONTROL S4

Бренд: Native Instruments Страницы: 86

Бренд: Native Instruments Страницы: 245

Бренд: PAT Страницы: 44

Бренд: Park Tool Страницы: 4

Бренд: Qlight Страницы: 4

Бренд: AMVAC Страницы: 81

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды