Cryomech CPA289C Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 64

background image

Specifications

5-8

8. High and Low Pressures

Displays a running average of the suction and discharge pressure.

9. Menu Button

Allows navigation to other screens, additional controls, and system information.

10. Operating Temperatures

Displays the coolant in and out temperature, helium temperature and oil temperature.

11. RJ45 Ethernet Port

Used for remote monitoring and control of the system via Modbus TCP protocol.

12. RS232 Port

Used for remote monitoring and control of the system via SMDP or Modbus RTU protocol.

13. RS485 Port

Used for remote monitoring and control of the system via SMDP or Modbus RTU protocol.

14. Running hours

Total number of hours the helium compressor package has run, this does not include idle time.

15. Software Version

Unique number used for tracking changes to the PLC program.

16. System I/O Port

Used to remotely control the helium compressor package and monitor a limited number of its
parameters.

17. USB Port

Used to update the helium compressor package software and download recorded data from
the PLC.

18. User Feedback Text

Displays the status of the helium compressor package including errors, warnings, cold head
rpm, and date and time.

«
...
26
27
28
29
30
...
»

Содержание CPA289C

































































Отзывы:

Нет отзывов

Похожие инструкции для CPA289C

Бренд: GALLERY Страницы: 18

Бренд: Raymarine Страницы: 70

Бренд: SALUDA MEDICAL Страницы: 61

Бренд: BARKO LOADERS Страницы: 85

Бренд: ECE Страницы: 2

Бренд: Ecco Страницы: 5

Evolution Series

Бренд: Bakare Страницы: 38

Бренд: xsto Страницы: 76

Бренд: F&V Страницы: 5

Бренд: F Care Systems Страницы: 2

Бренд: Qlight Страницы: 4

Бренд: T&D Страницы: 28

Бренд: XanLite Страницы: 2

Бренд: X-Rite Страницы: 6

Бренд: Yuwell Страницы: 2

PRO-FORM ab GLIDER

Бренд: ICON Health & Fitness Страницы: 16

Бренд: Hedson Страницы: 32

Бренд: JLG Страницы: 165

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды