Cryomech CPA289C Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 64

background image

Safety

3-3

CAUTION

Mounting the cold head in an orientation other than vertical will void the warranty without prior written
authorization from Cryomech, Inc.

CAUTION

Alterations to the cryocooler are prohibited without prior written authorization from Cryomech, Inc.
Modifications without prior written approval will void the warranty.

Section 6.1.6 Connect the remote motor assembly’s flex line- Remote Motor Cold Heads Only

CAUTION

Follow this procedure carefully when connecting and disconnecting the helium flex lines. Failure to follow
the procedure will void the warranty.

CAUTION

Do not allow the flex lines to contact any corrosives or commercial cleaning agents. Flex line damage
caused by exposure to corrosives or commercial cleaning agents will not be covered by the warranty.

CAUTION

Applying extreme bend stress to a flex line will cause permanent damage. Bending a flex line to less than
a 12 in (30 cm) radius will void the warranty.

Section 6.2 Compressor installation

CAUTION

Failure to follow these installation guidelines could result in voiding the warranty.

Section 6.2.1 Prepare the compressor package location

WARNING

The helium compressor package must be positioned to provide easy access to the front panel mounted
circuit breaker.

Section 6.2.2 Connect the water lines to the compressor

CAUTION

Cooling water must meet the requirements in Section 5. Introduction of cooling water that does not meet
the specifications in Section 5, even for cleaning purposes, it will void the warranty.

CAUTION

Do not apply heat to the cooling water inlet and outlet connectors located on the front panel of the helium
compressor package.

«
...
11
12
13
14
15
...
»

Содержание CPA289C

































































Отзывы:

Нет отзывов

Похожие инструкции для CPA289C

Бренд: Raymarine Страницы: 55

Бренд: Halyard Страницы: 4

Underwater Light Show & Fountain

Бренд: GAME Страницы: 2

Бренд: FagronLab Страницы: 16

Бренд: Zenbooth Страницы: 60

Бренд: Danelec Страницы: 67

Бренд: Xycom Страницы: 99

Бренд: Hagerman Страницы: 4

Бренд: hager Страницы: 2

TECSHOW QUAD SPIDER 60

Бренд: Ampro Страницы: 9

ULTRATHERM 908i

Бренд: gbo Страницы: 32

Бренд: Dantel Страницы: 6

Бренд: Zero 88 Страницы: 22

Бренд: Yaasa Страницы: 20

Бренд: Gaspardo Страницы: 88

Rack-mountable 8 x 8 USB 2.0 Interface with MX Core DSP Technology...

Бренд: M-Audio Страницы: 25

Бренд: Guyatone Страницы: 2

IQ Express RF6118

Бренд: Mainpine Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды