Cryomech CPA289C Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 64

background image

Safety

3-4

Section 6.2.3 Connect the compressor package to the main power

CAUTION

The mains supply voltage to the helium compressor package must be within 10% of the nominal voltage
specification in Section 5. Operating the helium compressor package outside the voltage specification
will void the warranty.

WARNING

Follow all local electrical codes and guidelines when during installation.

WARNING

One lead of the helium compressor package is grounded. Never bypass this ground or attach the helium
compressor package to an ungrounded circuit. A dangerous electrical hazard will develop.

Section 6.2.4 Connect the helium flex lines to the cold head or remote motor assembly and the
compressor package

CAUTION

Follow this procedure carefully when connecting and disconnecting the helium flex lines. Failure to follow
the procedure will void the warranty.

CAUTION

Do not allow the flex lines to contact any corrosives or commercial cleaning agents. Flex line damage
caused by exposure to corrosives or commercial cleaning agents will not be covered by the warranty.

CAUTION

Applying extreme bend stress to a flex line will cause permanent damage. Bending a flex line to less than
a 12 in (30 cm) radius will void the warranty.

3.2.3 Section 7: Operation

Section 7.1.1 Checks before operating

CAUTION

A voltage deviation of more than 10% above or below the voltage rating can cause helium compressor
motor overheating and possible failure. Indications of voltage operation outside that range will void the
helium compressor warranty.

CAUTION

Operating the cold head in a magnetic field of greater than 500 gauss will void the warranty.

«
...
12
13
14
15
16
...
»

Содержание CPA289C

































































Отзывы:

Нет отзывов

Похожие инструкции для CPA289C

Бренд: Campden instruments Страницы: 8

Бренд: K-9 Lights Страницы: 12

Бренд: Rane Страницы: 38

Бренд: Kartsana Страницы: 36

MIDORI ULB-50sc

Бренд: Ushio Страницы: 24

Бренд: Erbe Страницы: 124

SAS-1 Immunofix

Бренд: helena BioSciences Страницы: 48

Бренд: Hameg Страницы: 39

Бренд: Teac Страницы: 1

Бренд: Garelick Страницы: 2

Бренд: Reflex Marine Страницы: 36

Thermo Therapy TT-202

Бренд: Whitehall Страницы: 12

Бренд: Cattani Страницы: 99

CLAMP ON LEAK HiTESTER 3283

Бренд: Hioki Страницы: 64

Бренд: Nightowl Stage Lighting Страницы: 4

Бренд: Kärcher Страницы: 28

Бренд: Digilent Страницы: 14

Бренд: Fluke Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды