Cryomech CPA289C Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 64

background image

Safety

3-2

3.2 Warnings and cautions

The warnings and cautions for the Cryomech cryocooler are listed here by section. The same warnings
and cautions appear in each respective section.

3.2.1 Section 5: Specifications

Section 5.2 Technical specifications

CAUTION

Operation of the cryocooler in any situation that does not meet the specifications in this section will void
the warranty. If you plan to operate the system outside any of the specified conditions, contact Cryomech,
Inc.

CAUTION

The use of DI (De-Ionized) water is prohibited. DI water causes damage to the compressor package and
will not be covered under warranty.

3.2.2 Section 6: Installation

Section 6.1 Cold head installation

CAUTION

Failure to follow these installation guidelines will void the warranty.

CAUTION

Special care must be taken when handling the cold head. The warranty will not cover dented or bent
tubes.

CAUTION

Operating the cold head in a magnetic field of greater than 500 gauss will void the warranty.

Section 6.1.2 Initial preparation of the cold head

CAUTION

Heating any part of the cold head above 325 K (125 ºF, 52 ºC) will cause damage and void the warranty.

CAUTION

With the cold head oriented vertically, the maximum allowable load cannot exceed the value specified in
Section 5. Excessive loading will damage the cold head. This type of damage is not covered by the
warranty. If your application requires a load heavier than the weight specified in Section 5, prior written
authorization from Cryomech, Inc. must be granted.

«
...
10
11
12
13
14
...
»

Содержание CPA289C

































































Отзывы:

Нет отзывов

Похожие инструкции для CPA289C

Бренд: GE Страницы: 24

Бренд: e+p Elektrik Handels Страницы: 2

Бренд: Fagor Страницы: 12

Бренд: Baltic Страницы: 68

Бренд: H&S Страницы: 76

Бренд: EFX Страницы: 2

PRO-FORM ab GLIDER

Бренд: ICON Health & Fitness Страницы: 16

Бренд: Airway Страницы: 2

Бренд: Crazy Foil Страницы: 8

Бренд: Eleiko Страницы: 24

Бренд: Horizon Fitness Страницы: 17

Бренд: Wiltron Страницы: 13

Бренд: Vibration Research Страницы: 40

Бренд: Eco Stage Страницы: 17

Бренд: CDP Страницы: 20

Бренд: G-FITNESS Страницы: 26

SAMMONS PRESTON Rolyan A426112

Бренд: Patterson Medical Страницы: 6

Бренд: Casall Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды