Cryomech CPA289C Скачать руководство пользователя страница 55

Страница: 55 / 64

Operation

7-10

Warning Description

Explanation

“Helium Temp Running High!”

Helium discharge temperature approaching high error set point;
check cooling water temperatures, may also be caused by low
oil level check compressor module sight glasses or low oil
temperature caused by cool water

“Oil Temp Running High!”

Oil temperature approaching high error set point; verify cooling
water flow and temperatures

“Oil Temp Running Low!"

Oil temperature approaching low error set point; verify cooling
water flow and temperatures (reduce flow rate or increase
temperature)

7.7.7 Error and warning set points

The trip and clear set points for all the errors and warnings are listed in the following table.

Error Message

Lock Out

Contributor?

Trip

Clear

"High pressure too High!"

YES

400 psig (27.6bar)

375 psig (25.9 bar)

"High pressure too Low!"

YES

150 psig (10.3bar)

170 psig (11.7 bar)

“Low Pressure Too Low!”

YES

40 psig (2.8 bar)

50 psig (3.4 bar)

“Low Pressure Too High!"

YES

250 psig (17.2 bar)

240 psig (16.5 bar)

"Delta Pressure Too High!"

YES

300 psig (20.7bar)

290 psig (20bar)

"Delta Pressure Too Low!"

YES

50 psig (3.4 bar)

75 psig (5.2 bar)

"Static Pressure Too High!"

YES

300 psig (20.7 bar)

280 psig (19.3 bar)

"Static Pressure Too Low!"

YES

100 psig (6.9 bar)

170 psig (11.7 bar)

"Water In Temp Too High"

YES

110 °F (43 °C)

80 °F (27 °C)

"Water In Temp Too Low"

YES

40 °F (4 °C)

50 °F (10 °C)

“Water Out Temp Too High!”

YES

125 °F (52 °C)

110 °F (43 °C)

"Water Out Temp Too Low"

YES

40 °F (4 °C)

50 °F (10 °C)

“Helium Temp Too High!”

YES

190 °F (88 °C)

120 °F (49 °C)

“Helium Temp Too Low!"

YES

40 °F (4 °C)

50 °F (10 °C)

“Oil Temp Too High!”

YES

125 °F (52 °C)

110 °F (43 °C)

“Oil Temp Too Low!"

YES

40 °F (4 °C)

50 °F (10 °C)

“Compressor Motor Current Too
Low!”

YES

< 5A

≥ 5 A

Содержание CPA289C

































































Результаты поиска

Содержание CPA289C

Отзывы:

Похожие инструкции для CPA289C

Бренды по названию

Популярные бренды

Cryomech CPA289C, Инструкция по установке и эксплуатации

Результаты поиска

Содержание CPA289C

Отзывы:

Похожие инструкции для CPA289C

Бренды по названию

Популярные бренды