Cornelius SPIRIT Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 41

background image

1

317961000

SAFETY INFORMATION

Recognize Safety Information

This is the safety-alert symbol. When you see this
symbol on our machine or in this manual, be alert to
the potentially of personal injury.

Follow recommended precautions and safe operating
practices.

DANGER

Understand Signal Words

A signal word - DANGER, WARNING, OR CAUTION
is used with the safety-alert symbol. DANGER identi-
fies the most serious hazards.

Safety signs with signal word DANGER or WARNING
are typically near specific hazards.

WARNING

General precautions are listed on CAUTION safety
signs. CAUTION also calls attention to safety mes-
sages in this manual.

CAUTION

Follow Safety Instructions

Carefully read all safety messages in this manual and on your machine safety signs. Keep safety signs in
good condition. Replace missing or damaged safety signs. Learn how to operate the machine and how to
use the controls properly. Do not let anyone operate the machine without instructions. Keep your machine in
proper working condition. Unauthorized modifications to the machine may impair function and/or safety and
affect the machine life.

CO

2

(Carbon Dioxide) Warning

CO

2

Displaces Oxygen. Strict Attention must be observed in the prevention of CO

2

(carbon dioxide)

gas leaks in the entire CO

2

and soft drink system. If a CO

2

gas leak is suspected, particularly in a

small area, immediately ventilate the contaminated area before attempting to repair the leak. Person-
nel exposed to high concentration of CO

2

gas will experience tremors which are followed rapidly by

loss of consciousness and suffocation.

CAUTION: Before shipping, storing, or relocating this Unit, the syrup systems must be sanitized and
all sanitizing solution must be purged from the syrup systems. All water must also be purged from
the plain and carbonated water systems. A freezing ambient temperature will cause residual water
remaining inside the Unit to freeze resulting in damage to internal components of the Unit.

Shipping, Storing, Or Relocating Unit

«
...
3
4
5
6
7
...
»

Содержание SPIRIT










































Отзывы:

Нет отзывов

Похожие инструкции для SPIRIT

HydroChill HCF090

Бренд: Zip Страницы: 36

Бренд: First Sales Страницы: 27

600 LFCV Series

Бренд: lancer Страницы: 32

ADIKI300-01 Series

Бренд: ADIR Страницы: 18

Бренд: Hilti Страницы: 13

Бренд: Hilti Страницы: 40

Бренд: Hilti Страницы: 280

Бренд: Hilti Страницы: 274

Бренд: COX Страницы: 2

Бренд: Coway Страницы: 24

Бренд: Bobrick Страницы: 2

PAW-TD20C1E5-UK

Бренд: eco3energy Страницы: 16

Бренд: Strong Flow Страницы: 22

Бренд: Tatung Страницы: 4

BrassMaster Series

Бренд: Water Control Страницы: 2

Бренд: Bunn Страницы: 25

Бренд: Graff Страницы: 3

Бренд: Bunn Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды